Question 28 65 pts Aspur gear has a diametral pitch of 6 teethin, 20 teeth 20...
Question #5 (20 pts) A pinion has 18 teeth and a diametral pitch of 9 teeth/in, a face width of 1,5 in sa pressure angle of 20° with full-depth teeth. The spur gear is made by the milling or emin required to transmit at least 11 hp horsepower with a corresponding speed and moderate applications. Which material is the best choice for the spu ones in Table 5 considering the maximum allowable bending stres (factor of safety, nd-2.5)? U quations...
6) [20 pts) Bending Stress in a Gear A steel spur pinion has a pitch of 6 teeth/in, 22 full-depth teeth with a cut profile, and a 20° pressure angle. The pinion runs at a speed of 1280 rev/min and transmits 15 hp to a 60-tooth gear. If the face width is 2 in., estimate the bending stress. Take the value of Lewis form factor, Y, from the table 14-2. The bending stress is kpsi.
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
(1 ) Problem 2: A 20° full-depth steel (milled profile) spur pinion has a diametral pitch of 8 teeth/in and 30 teeth and transmits 5 hp at a speed of 150 rev/min. Determine an appropriate face width if the allowable bending stress is 24 kpsi. Consider factor of safety is 1.28. (35) Problem 3: A plain ended helical compression spring is to be made of music in spring index of 8. This spring has 10 moilo
A helical gear has a normal diametral pitch of 24, a normal pressure angle of 14 ½ o, 72 teeth, a face width of 0.25 in and helix angle of 45° The power comes from an electric motor, and the drive is to winch that will experience moderate shock. (a) If the gear transmits 0.50 HP at a speed of 3450 RPM, what would be the tangential force? (b) If the gear operates with a pinion having 16 teeth, what...
4. Gear bending stress. Consider just the pair Gear 1 and 2. Gears are all 20º pressure angle with a milled profile and a face width of ¼”. Let the transmitted load be 14.0 lbf and the pitch-line velocity be 1178 ft/min. a) What is Y for 20 and 80 teeth? b) What is Kv? c) What is the bending stress on Gear 1, in psi? d) What is the bending stress on Gear 2?
Please help.
Thx
Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a pitch diameter of 2 inches, and has 20 teeth. The gear "Ghas 120 teeth. All teeth have a pressure angle of 20, full-depth, hobbed profile, and a face width of 0.5 inches. All materials are steel. Determine: A) Minimum number of pinion teeth: Np,min This shows that...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a pinion directly above it. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. Figure P12-1 Shaft carrying a gear and a V-belt drive 0
See Figure P12-1. The shaft rotating...
1. A commercial straight pinion has an 8 teeth / in. Diametric pitch, a 1.5 in. Face width, 16 teeth and a 20 pressure angle with full height teeth (calculating the Kx speed maker considering a milled profile). To be mated with a 50-tooth crown made of cast iron ASTM No. 50. With a tangential load of 382 lbf, estimate the safety factor of the transmission, based on the possibility of fatigue failure on the surface.
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is 2 in. The pinion rotates at 1000 rev/min and transmits 50 hp. The shafts are at 90. Determine the components of the gear tooth force and show these on a sketch of the ge
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is...