A uniform rectangular block is being held on cart by a hinge at Point A and a roller at Point B (i.e. the block is not attached to Point B and force applied to the block at B is only in the x-direction). The cart is accelerating to the left at 3 m/s. What are the forces being applied to the block at Point A and Point B?
At what value of acceleration would the block begin to lose contact with the roller at Point B?
Homework Answers
Please Thumbs Up....
Add Answer to:
A uniform rectangular block is being held on cart by a hinge at
Point A and...
b. A uniform rectangular block is being held on cart by a hinge at Point A...
b. A uniform rectangular block is being held on cart by a hinge at Point A and a roller at Point B (i.e. the block is not attached to Point B and force applied to the block at B is only in the x- direction). The cart is accelerating to the left at 3 m/s. What are the forces being applied to the block at Point A and Point B? 10 kg 0.3 m C. Above what cart acceleration will...
1-A 10 m long bar is attached by a frictionless hinge to a wall and held...
1-A 10 m long bar is attached by a frictionless hinge to a wall and held horizontal by a rope that makes an angle of 53 with the bar. the bar is uniform and weights 40N. a)how far from the hinge should a 10 kg mass be suspended for the tension T in the rope to be 100 N? b) determine the vertical component of the force exerted by the hinge on the bar. --------------------------------------------------------------------------------------------------------------------------------------------------------------------- 2- A traffic light hangs...
The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge...
The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle 0 = 42° by a brace that is attached to a pin. The beam has a weight of 350 N. Three additional forces keep the beam in equilibrium. The brace applies a force to the right end of the beam that is directed upward at the angle with respect to the horizontal. The hinge applies a force...
A uniform rod is attached to a wall by a hinge at its base. The rod...
A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 6.00 kq, a length of 1.55 m, is at an angle of 29.0° above the horizontal, and is held in place by a horizontal cord attached to the other end of the rod and bolted to the wall above the base of the rod. (a) Determine the tension in the cord. (b) Determine the horizontal and vertical components of the...
1 point) A block of ice is held 2 m below the surface of the water...
1 point) A block of ice is held 2 m below the surface of the water and then released. What is the magnitude of its initial acceleration? (calculators permitted in this question) m/s2 If its mass is 1.9 kg and its frictional factor is 3 kg/s, what is the terminal upward speed? (Use 920 kg/m2 for the density of ice.) Hint: Use Eqn 13-11, and think about how you need to balance the bouyant, gravitational, and drag forces if you...
A uniform drawbridge must be held at a 37 ∘ angle above the horizontal to allow...
A uniform drawbridge must be held at a 37 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45,000 N and is 14.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. A)What is the tension in the cable? B)Find the magnitude of the force the hinge exerts on the bridge. C)Find the direction...
A pendulum is attached to the cart that has a mass of 3m and that is...
A pendulum is attached to the cart that has a mass of 3m and that is free to move along the horizontal direction. From the rest condition, when the lumped mass m of the pendulum makes a 0 angle with the vertical, the pendulum is released. 3m L m Compared to the case in which the cart is fixed (it cannot move), when 0=0°, the speed of the lumped mass at the tip of the pendulum would be smaller. (Vcartmoves...
(14.2) A block of mass m = 10 kg riding on a frictionless horizontal plane is...
(14.2) A block of mass m = 10 kg riding on a frictionless horizontal plane is subjected to five forces. The weight of the block and the normal force of contact with the plane both act in the vertical direction, cancel, and may be henceforth ignored. Three applied forces, →F1 , →F2 , →F3 , act horizontally on the block. The information that we have been able to gather about the applied forces is summarised as follows: F1 = 10...
A uniform drawbridge must be held at a 33.5 ∘∘ angle above the horizontal to allow...
A uniform drawbridge must be held at a 33.5 ∘∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 44000 NN, is 10.5 mm long, and pivots about a hinge at its lower end. A cable is connected 3.80 mm from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. A. What is the tension in the cable? B. Find the magnitude of the force the hinge...
A uniform 6-m high, 10-m wide (into the page) rectangular gate is hinged at Point A....
A uniform 6-m high, 10-m wide (into the page) rectangular gate
is hinged at Point A. The right side of the gate is exposed to the
atmosphere while the left side is partially covered by 2 different
fluids (oil as top layer and water as bottom layer). The free
surface of the oil is 1 m below the hinge at Point A. The oil layer
(SG = 0.8) is 2-m thick while the water layer is 3-m thick.
Assuming the...
b. A uniform rectangular block is being held on cart by a hinge at Point A and a roller at Point B (i.e. the block is not attached to Point B and force applied to the block at B is only in the x- direction). The cart is accelerating to the left at 3 m/s. What are the forces being applied to the block at Point A and Point B? 10 kg 0.3 m C. Above what cart acceleration will...
The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle 0 = 42° by a brace that is attached to a pin. The beam has a weight of 350 N. Three additional forces keep the beam in equilibrium. The brace applies a force to the right end of the beam that is directed upward at the angle with respect to the horizontal. The hinge applies a force...
A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 6.00 kq, a length of 1.55 m, is at an angle of 29.0° above the horizontal, and is held in place by a horizontal cord attached to the other end of the rod and bolted to the wall above the base of the rod. (a) Determine the tension in the cord. (b) Determine the horizontal and vertical components of the...
1 point) A block of ice is held 2 m below the surface of the water and then released. What is the magnitude of its initial acceleration? (calculators permitted in this question) m/s2 If its mass is 1.9 kg and its frictional factor is 3 kg/s, what is the terminal upward speed? (Use 920 kg/m2 for the density of ice.) Hint: Use Eqn 13-11, and think about how you need to balance the bouyant, gravitational, and drag forces if you...
A pendulum is attached to the cart that has a mass of 3m and that is free to move along the horizontal direction. From the rest condition, when the lumped mass m of the pendulum makes a 0 angle with the vertical, the pendulum is released. 3m L m Compared to the case in which the cart is fixed (it cannot move), when 0=0°, the speed of the lumped mass at the tip of the pendulum would be smaller. (Vcartmoves...
A uniform 6-m high, 10-m wide (into the page) rectangular gate
is hinged at Point A. The right side of the gate is exposed to the
atmosphere while the left side is partially covered by 2 different
fluids (oil as top layer and water as bottom layer). The free
surface of the oil is 1 m below the hinge at Point A. The oil layer
(SG = 0.8) is 2-m thick while the water layer is 3-m thick.
Assuming the...
Most questions answered within 3 hours.
-
You capture data by having 8 people fill in 30 small dots on a
piece of...
asked 3 hours ago -
What are the z-values such that 70% of the area lies in the
middle of the...
asked 5 hours ago -
You borrow $29,500 to purchase a brand new car. The interest
rate is 6%, and the...
asked 4 hours ago -
The amount of time it takes an asteroid, whose average distance
from the Sun is 4.70...
asked 5 hours ago -
A 0.289 kg mass slides on a frictionless floor with a speed of
1.34 m/s. The...
asked 5 hours ago -
15.A box contains five red balls, three green balls, and two
yellow balls. Suppose you select...
asked 7 hours ago -
Assume you are given the following for Stackelberg industries:
Return on Assets (ROA) = 8%
Debt...
asked 6 hours ago -
an engineer proposes to use mmWave in 5G network to
increase data rate.
What are the...
asked 6 hours ago -
Explain the idea behind using SEMIJOIN in distributed
query processing.
asked 6 hours ago -
why
is context important in selecting and applying guidelines and
principles for interface design?
illustrate your...
asked 6 hours ago -
In a certain board game, a player rolls two fair six-sided dice
until the player rolls...
asked 7 hours ago -
You are going to deposit $3,200 in an account that pays .58
percent interest compounded quarterly....
asked 6 hours ago