Feel free to ask doubts in comment section...
Rate and support...
A water jet with a velocity of V; -8 m/s and jet diameter D; -10 cm...
A 10 cm jet of water issues from a 1 m diameter tank Assume that the velocity in the jet is /2gh m/s where h is the elevation of the water surface above the outlet jet. How long will it take for the water surface in the tank to drop from ho 2 m to h 0.50 m? Problem Definition Situation: Water draining by a 10 cm jet from 1 m diameter tank. Find: Time (in seconds) to drain from...
7. Water flows through a pipe of diameter 1.08m at a velocity of 2m/s. If someone puts a nozzle on the end of the pipe, reducing the diameter to 0.35m, at what speed will the water exit the pipe?. 10. A pipe with a radius of 50 cm has water flowing at 5 m/s. If water goes into a new pipe with radius 33 cm, how much will the pressure decrease? 11. A large dam has a hole that is...
V cart Nozzle V. jet- 4. (20 pts) A 3-cm-diameter water jet moving at 40 m/s velocity in x-direction strikes the vertical back surface of a cart moving horizontally at a constant speed of 10 m/s in the flow direction. After the strike, the water stream splatters off in all directions in the plane of the back surface. Using the moving control volume indicated with dashed lines in the figure, determine: Waterjeti F. Rx X a) The relative velocity and...
A vane on wheels moves with constant velocity 0.58 m/s when a stream of water having .( a nozzle exit velocity 1.83 m/s and 5 cm diameter is turned at 8 = 45° by the vane as indicated in the figure below. Neglect friction so that the speed of the water jet relative to the vane is unchanged result of the Bernoulli equation if elevation of the water jet is .neglected (Determine the reaction force (N) in the x-direction (RX...
Two objects are moving in the xy-plane. Object A has a mass of 3.2 kg and has a velocity vA = < 2.3 m/s, 4.2 m/s > and object B has a mass of 2.9 kg and has a velocity vB = < -1.8 m/s, 2.7 m/s > . What is the total momentum of the system? A uniform sphere of radius 2R has a spherical cavity of radius R cut out of it. The center of the cavity is...
Water is flowing through a 10-cm diameter water pipe at a rate
of 0.2 m^3/s. Now a diffuser with an outlet diameter of 20 cm is
bolted to the pipe in order to slow down water that exits into the
atmosphere, as shown. Disregarding frictional effects, determine
the force exerted on the flange due to the water flow. Density of
water = 1,000 kg/m^3.
+ d = 10 cm D = 20 cm Diffuser
a 50-mm-diameter jet of water impacts a vane at a
velocity of 20 m/s as shown in Figure 4.78. The vane has a mass of
90 kg, and it deflects the jet through a 55° angle. The vane is
constrained to move in the direction of the incoming jet, and there
is no force opposing the motion of the vane. Determine the
acceleration of the vane when it was first released. Assume water
at 20°C
Mecánica de fluidos Problemas A...
Question 8: Water exits a pipe of diameter 2.0 cm with speed 5.0 m/s. Assume atmospheric pressure at the exit. What is the pressure where the pipe diameter is 4.0 cm and 3.0 m below the exit? 20 cm 3.0m YOL cm
Question 8: Water exits a pipe of diameter 2.0 cm with speed 5.0 m/s. Assume atmospheric pressure at the exit. What is the pressure where the pipe diameter is 4.0 cm and 3.0 m below the exit? 20 cm 3.0m YOL cm
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m/s. Then, a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water as it exits the diffuser to atmospheric pressure, as shown in the given figure. Disregarding frictional effects, determine the force exerted on the bolts due to the water flow. Take the density of water to be 1000 kg/m3 -t- d 10 cmm D = 20...