1a. What will be the outcome for the following?
pinMode(9,OUTPUT);
analogWrite(9,63.5);
a. A pulse width modulated generated signal for 63.5
milliseconds
b. A square wave generated signal with output voltage
of
6.3V
c. A square wave signal of 1.25V is generated on channel 9
d. None
What will be the outcome for the following?
pinMode(9,OUTPUT);
analogWrite(9,63.5);
Answer:
b. A square wave generated signal with output voltage of
6.3 V.
Explanation:
pinMode(9,OUTPUT) - > set the digital pin 9 as output
analogWrite(9,63.5) -> generates square wave with voltage 6.3V
So a square wave generated with output voltage of 6.3V
1a. What will be the outcome for the following? pinMode(9,OUTPUT); analogWrite(9,63.5); a. A pulse width modulated...
Problem 31: (34 points) 1. (10 points) A pulse width modulated (PWM) signal fPwM(t) in Figure 2. The symbol D represents a duty cycle, a number between zero and one. Determine the compact trigonometric Fourier series coefficients (Co Cn, θ.) of the signal f(t) 2. (10 points) One use of PWM is to generate variable DC voltages. While the PWM signal is not DC, you should be able to see from your results in part 1 that it has a...
Fuel injectors use what kind of computer output signals? A. Switched voltage B. Switched ground C. Constant frequency pulse width modulated D. Variable frequency pulse width modulated
Problem 31: (34 points) 1. (10 points) A pulse width modulated (PWM) signal fPwM(t) in Figure 2. The symbol D represents a duty cycle, a number between zero and one. Determine the compact trigonometric Fourier series coefficients (Co C,11 %) of the signal f(t). 2. (10 points) One use of PWM is to generate variable DC voltages. While the PWM signal is not DC, you should be able to see from your results in part 1 that it hss a...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...
a b c d b. What is the output noise power, PSy Uaj.p A certain communication channel is characterized by K noise with power-spectral density of S) 10-10 w The message signal that is to be 3. 10-9 attenuation and additive white transmitted through this channel is m (t) # 50 Cos (10000?), and the carrier signal that will be used in each ofthe following modulation schemes is c(t) = 100 Cos (40000m). n(t) 20 m(t) x() Channel wit (0...
answere Please mark only one of the four choices Q1. Controlling the speed of a DC motor by using a micro-controller, is what type of control? b. Digital C. Analog d. All of the above Q2. When current flow is interrupted in a DC motor, which motor property causes a reverse voltage spike? a. Resistance b. Capacitance C. Inductance d. None of the above Q3. Which Arduino internal circuit is used to control motor speed? a. Digital to Analog Converter...
please the answer it doesn't really matter, I really need a good explanation of how to clearly understand this please show your working if you can also please with a readable handwriting 23. WAVES a. Explain the difference between transverse and longitudinal waves. f(t)-A sin(wt + φ) Consider the following sine wave: b. Explain the name and function of A, a, and ф. Give units of measure, if relevant. c. What is the value of w for a 50Hz sinusoidal...
Questions 4-20. Questions 4-20. QUESTION 4 the output becomes The longer a signal is applied to the input of an integrator op amp, the a smaller b. larger QUESTION 5 the output becomes. The faster the voltage applied to the input of a differentiator changes, the a smaller . b. larger QUESTION 6 voltage than for a negative-going signal. A Schmitt trigger switching threshold for a positive-going input signal is at a a lesser . b.greater QUESTION 7 If a...
A modulated voltage signal is given as: s(t) = 10(1 + 0.5cos(10²πt)) cos(106πt) volts. a) Plot the spectrum of the signal and calculate its bandwidth. b) Calculate the total signal power in dbm. c) If the message signal is a single-tone signal, explain if this is an AM-DSB-SC or an AM-DSB-C signal. What is the modulation efficiency? d) The signal s(t) is passed through the following system. Find the output mout(t) as a function of time and its Fourier transform, Mout(f).
Question A modulated voltage signal is given as: s(t) = 10(1 + 0.5cos(10?rt)) cos(106mt) volts. Plot the spectrum of the signal and calculate its bandwidth. b) Calculate the total signal power in dbm. c) If the message signal is a single-tone signal, explain if this is an AM-DSB-SC or an AM-DSB-C signal. What is the modulation efficiency? d) The signal s(t) is passed through the following system. Find the output mout(t) as a function of time and its Fourier transform,...