Homework Answers
Add Answer to:
(12 %) Members ABC and CDE are two continuous members pinned at C and all members...
Check My Work The continuous frame ABC has a pinned support at A, a guided support...
Check My Work The continuous frame ABC has a pinned support at A, a guided support at C, and a rigid corner connection at B (see figure). Members AB and BC each have length 1 and flexural rigidity EI. A horizontal force Pacts at midheight of member AB MC Find all reactions of the frame. (a) Enter VA (b) Enter HA C) Enter Ho (d) What is the largest bending moment Mmax in the frame? (Note: Disregard axial deformations in...
[Quiz#03]: Members ABC and BD of the counter chair are rigidly connected at B and the...
[Quiz#03]: Members ABC and BD of the counter chair are rigidly connected at B and the smooth collar at D is allowed to move freely along the vertical slot. a) Draw the shear and bending moment diagrams for member ABC. [12 marks] b) For the given cross section for member ABC determine the centroid and the moment of inertia (1) with respect to Neutral Axis. [12 marks] c) If the maximum bending moment is 225 lb-ft, determine the maximum absolute...
For the system shown below, the surface at G is smooth, all members are of negligible...
For the system shown below, the surface at G is smooth, all
members are of negligible weight, the pulley is frictionless, and
the cable is inextensible
.Answer all parts of the problem below
A) Are there any two force members? If so, circle the two force
member(s) in the diagram, or write them below:
B) Determine the force in member BE.
C) Determine the components of the force acting on pin C.
D) Determine the force of wheel on the...
The gate ABC below is free at A, pinned at B, and pushes against a smooth...
The gate ABC below is free at A, pinned at B, and pushes against a smooth stopper at C. It is 1 m wide (i.e., out of the page). If L = 2 m, determine the force the gate exerts at C. pw 1.0 Mg/m3, g 9.81 m/s2 p p*g*h w= p*b 4 m A 2 m C
please show all steps 3. The truss has a pinned support at A and a roller...
please show all steps
3. The truss has a pinned support at A and a roller support at C. i. If P = 0 kN and P2 = 5 kN, list all of the zero-force members in the truss (10 points) ii. If P1 = 30 kN and P2 = 16 kN, the support reaction at C is Roy = 28 kN (pointing up) Determine the forces in all members of the truss. Clearly indicate if each member is in...
1) Rigid bar ABC is supported by pin-connected axial member (1) and by a pin connection...
1) Rigid bar ABC is supported by pin-connected axial member (1) and by a pin connection at C, as shown in the figure. A concentrated load is applied to the rigid bar at A. Assume P = 5,300 b, a = 20 in, b= 30 in., c = 13 in., and d = 28 in. Determine the magnitude of the maximum internal shear force within pin C. A. 3670 lb B. 3720 lb C. 3850 lb D. 3940 lb E....
-:37 PM Wed Oct 30 2 KN I KN 2 KN TIN DE 8 3. Determine...
-:37 PM Wed Oct 30 2 KN I KN 2 KN TIN DE 8 3. Determine the force in members DF, DG, and EG using method of sections. Determine the force in member DE using method of joints. State whether the members are in tension or compression. C 12 m2 m2 m2 m2 m2 m
a. Specify the type of compound truss shown in Figure 2. Assume all members are pin...
a. Specify the type of compound truss shown in Figure 2. Assume all members are pin connected. The truss is pin supported at A and roller supported at F. Investigate the determinacy and stability of the truss Using the method of section, determine the force in member CD. State if the member is in b. c. tension or compression d. Using the method of joint, determine the force in members JK and JN. State if the members are in tension...
Using the method of sections, determine the forces in the indicated members of the trusses shown...
Using the method of sections, determine the forces in the indicated members of the trusses shown and state if the member is in tension or compression. In addition, summarize the results on a force summation diagram. Notes: o Answers without a force summation diagram will receive a score of zero. Be sure to draw the free-body diagram(s) of the portion(s) of the section(s) used for analysis. Answers without the diagram(s) will receive a score of zero. Show your work. Answers...
Beam ABC as shown in figure 2 is supported as fixed at A, a cable tie...
Beam ABC as shown in figure 2 is supported as fixed at A, a cable tie at B and a spring at C carries a uniformly distributed load of 72 kN/m on member AB and a concentrated load of 54 kN on member BC. Using the flexibility method and neglect the axial effects in the bcam, (a) perform the global flexibility matrix of the beam structure, (b) calculate the rotation at B and displacement at C, (c) draw the deflection,...
Check My Work The continuous frame ABC has a pinned support at A, a guided support at C, and a rigid corner connection at B (see figure). Members AB and BC each have length 1 and flexural rigidity EI. A horizontal force Pacts at midheight of member AB MC Find all reactions of the frame. (a) Enter VA (b) Enter HA C) Enter Ho (d) What is the largest bending moment Mmax in the frame? (Note: Disregard axial deformations in...
[Quiz#03]: Members ABC and BD of the counter chair are rigidly connected at B and the smooth collar at D is allowed to move freely along the vertical slot. a) Draw the shear and bending moment diagrams for member ABC. [12 marks] b) For the given cross section for member ABC determine the centroid and the moment of inertia (1) with respect to Neutral Axis. [12 marks] c) If the maximum bending moment is 225 lb-ft, determine the maximum absolute...
For the system shown below, the surface at G is smooth, all
members are of negligible weight, the pulley is frictionless, and
the cable is inextensible
.Answer all parts of the problem below
A) Are there any two force members? If so, circle the two force
member(s) in the diagram, or write them below:
B) Determine the force in member BE.
C) Determine the components of the force acting on pin C.
D) Determine the force of wheel on the...
The gate ABC below is free at A, pinned at B, and pushes against a smooth stopper at C. It is 1 m wide (i.e., out of the page). If L = 2 m, determine the force the gate exerts at C. pw 1.0 Mg/m3, g 9.81 m/s2 p p*g*h w= p*b 4 m A 2 m C
please show all steps
3. The truss has a pinned support at A and a roller support at C. i. If P = 0 kN and P2 = 5 kN, list all of the zero-force members in the truss (10 points) ii. If P1 = 30 kN and P2 = 16 kN, the support reaction at C is Roy = 28 kN (pointing up) Determine the forces in all members of the truss. Clearly indicate if each member is in...
1) Rigid bar ABC is supported by pin-connected axial member (1) and by a pin connection at C, as shown in the figure. A concentrated load is applied to the rigid bar at A. Assume P = 5,300 b, a = 20 in, b= 30 in., c = 13 in., and d = 28 in. Determine the magnitude of the maximum internal shear force within pin C. A. 3670 lb B. 3720 lb C. 3850 lb D. 3940 lb E....
-:37 PM Wed Oct 30 2 KN I KN 2 KN TIN DE 8 3. Determine the force in members DF, DG, and EG using method of sections. Determine the force in member DE using method of joints. State whether the members are in tension or compression. C 12 m2 m2 m2 m2 m2 m
a. Specify the type of compound truss shown in Figure 2. Assume all members are pin connected. The truss is pin supported at A and roller supported at F. Investigate the determinacy and stability of the truss Using the method of section, determine the force in member CD. State if the member is in b. c. tension or compression d. Using the method of joint, determine the force in members JK and JN. State if the members are in tension...
Using the method of sections, determine the forces in the indicated members of the trusses shown and state if the member is in tension or compression. In addition, summarize the results on a force summation diagram. Notes: o Answers without a force summation diagram will receive a score of zero. Be sure to draw the free-body diagram(s) of the portion(s) of the section(s) used for analysis. Answers without the diagram(s) will receive a score of zero. Show your work. Answers...
Beam ABC as shown in figure 2 is supported as fixed at A, a cable tie at B and a spring at C carries a uniformly distributed load of 72 kN/m on member AB and a concentrated load of 54 kN on member BC. Using the flexibility method and neglect the axial effects in the bcam, (a) perform the global flexibility matrix of the beam structure, (b) calculate the rotation at B and displacement at C, (c) draw the deflection,...
Most questions answered within 3 hours.
-
What is the % w/v when 80 mL of a 2.0% solution is mixed with 50...
asked 3 minutes ago -
How can I solve the following using a TI83
Claim: Most adults would erase all of...
asked 16 minutes ago -
Analysis of 3-ethyl-3-buten-2-ol gave C, 72.13%; H, 11.92%.
Calculate the percent deviation of these results from...
asked 13 minutes ago -
Which VALS segment is most likely to have a top of the line
brand new (2015)...
asked 17 minutes ago -
Write a program to score the paper-rock-scissor game. Each of
two users types in either P,R...
asked 37 minutes ago -
Calculate the equillibrium constent K for a redox reaction that
has E°cell = -.98 V at...
asked 49 minutes ago -
A concave spherical mirror has a radius of curvature of
magnitude 19.6 cm.
(a) Find the...
asked 51 minutes ago -
3. draw a diagram of the magnetic field:
a. around a long straight wire with a...
asked 49 minutes ago -
If you titrated 30.0 mL of 0.1 M HCl with 0.1 M NaOH, indicate
the approximate...
asked 58 minutes ago -
NADH passes electrons into the electron transport chain. List
the carriers that would receive the electrons,...
asked 1 hour ago -
A cylindrical cable with a resistivity of 1.6x10-8 Ω·m and cross
sectional area of 3x10-5 m^2...
asked 1 hour ago -
True or False.
A consumer with convex preferences who is indifferent between
the bundles (5,2) and...
asked 1 hour ago