3. If the elongation of wire BD is 0.07 inch after the force P is applied,...

Question

Question

Answer 1

Answer #1

$d o.251n 29χ. \ D11S:, В): o.oz1n , 3 LO 1bD 3 1323, 9 구$

Answer 2

Similar Homework Help Questions

Shown in the table are data for the tensile force applied to a steel specimen in...

Shown in the table are data for the tensile force applied to a steel specimen in thousands of pounds, and y is the resulting elongation in thousands of an inch. construct a 95% confidence interval for B, the elongation per thousand pounds of tensile stress. 1. Determine the least squares estimator Sex Tensile force Elongation 2. Determine the value se? applied (thousandths (thousands of of an inch) 3. The t value for this Cl is: pounds) 4. The lower limit...
If the applied force P causes the point B on the rigid arm ABC to be displaced 0.25 mm downward

If the applied force P causes the point B on the rigid arm ABC to be displaced 0.25 mm downward, determine the normal strain developed in wires BD and CE.
Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240...

Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm2. Link CE is made of aluminium (E 72 GPa) and has a cross-sectional area of 300 mm2. Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.36 mm. (Round the final answer to two decimal places.) 995 mm A 150 mm E 225...

A force and a temperature change were applied to a member. What is the elongation of...

A force and a temperature change were applied to a member. What is the elongation of the following member in inches (to the nearest 0.0001)? a=15 x 1061/°F P = 452 kip L = 33 in To = 62°F Tp = 56 °F E = 10,877 ksi A = 1 in 2 Р b The following cross section has a moment applied around the local X axis (horizontal axis at the centroid). Determine the maximum TENSILE stress in ksi to...
P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used...

P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 124 MPa and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD 1.8 m 1.8 m 1.35 m
(1 point) In a uniaxial test, a force applied along the axis of a steel cylindrical...

(1 point) In a uniaxial test, a force applied along the axis of a steel cylindrical specimen causes elastic deformation. Given that its initial diameter is 25 mm, determine the magnitude of this force that will produce a 6 mm elastic change in diameter. For steel, v = 0.30 and E = 207 GPa.

A force P is applied on the crate at A as shown. Determine

A force P is applied on the crate at A as shown. Determine(a) the moment of the force P about C,(b) the magnitude and sense of the vertical force applied at E that creates the same moment about C,(c) the magnitude and direction (from horizontal) of the smallest force applied at E that creates the same moment about C.If P=500 N, a=25°, a=300 mm, b=500 mm, c=350 mm, d=50 mma) Moment of P about C(N · m, 3 sigfig, CW+)=b)...
Q1. A circular rod of 12 mm diameter was tested for tension. The total elongation on...

Q1. A circular rod of 12 mm diameter was tested for tension. The total elongation on a 300 mm length was 0.22 mm under a tensile load of 17 KN. Find the value of E. (2.5 Marks) Answer: Q2. A prismatic bar has a cross section of 25 mm x 50 mm and a length of 2m under an axial force of 90 KN. The measured elongation of the bar is 1.5 mm. Compute the tensile stress and strain in...
1. (8 points) Determine the maximum force P that can be applied so that the steel...

1. (8 points) Determine the maximum force P that can be applied so that the steel rod AB does not buckle. The rod has a diameter of 1 in. Pinned support at both ends. F.S.=2 , E=29x103ksi, and Oy=50ksi. A wift*24 3ft

A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate...

A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate (see figures. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has diameter 30 mm, the brass tube has outer diameter 45 mm, and the copper tube has outer diameter 60 mm. The corresponding moduli of elasticity are = 210 GPa = 100 GPa, and E= 120 GPa. Calculate the compressive stresses and in the steel,...