sketch the top, front and right side views using third- angle projection full scale FRONT BOTTOM...

Question

Question

sketch the top, front and right side views using third- angle projection full scale

Answer 1

Answer #1

Top view Left site view FRONT VREW

Answer 2

Similar Homework Help Questions

Sketch front, right side, left side, bottom and back views. sketch: Front, Right side, Left Side. Bottom & Back Views 8 sketch: Front, Right side, Left Side. Bottom & Back Views 8

Sketch front, right side, left side, bottom and back views. sketch: Front, Right side, Left Side. Bottom & Back Views 8 sketch: Front, Right side, Left Side. Bottom & Back Views 8
housing 01.90 02.50 01.25 1.00 1.00 5X R.50 50 0.40 ROUNDS& FILLETS R.10 50 1.00 .50 1.00 1.50 50 00 2.00 .95 2.00 1...

housing 01.90 02.50 01.25 1.00 1.00 5X R.50 50 0.40 ROUNDS& FILLETS R.10 50 1.00 .50 1.00 1.50 50 00 2.00 .95 2.00 1.60 0.60 .40 X 0.40 SLOTS 50 50 1.00 .60 GUIDE BRACKET 40 0.90 03.00 HOUSING ASSIGNMENT: ON A ONE-INCH GRID SHEET (.10 IN. SQUARES) SKETCH THE TOP FRONT AND RIGHT SIDE VIEWS OF ONE OF THE PARTS SHOWN USING THIRD-ANGLE ORTHOGRAPHIC PROJECTION. ALLOW APPROXIMATELY 1.00 IN. BETWEEN VIEWS. DO NOT DIMENSION NOTE: ARROW INDICATES DIRECTION OF...
Exercise 4.9, page 172. Sketch front, top, and right-side views for # 1 on grid paper...

Exercise 4.9, page 172. Sketch front, top, and right-side views for # 1 on grid paper or directly in CAD. Scale drawing to fit paper. Shaw all dimensions. Add a bilateral angular tolerance of +/-1 0.5° to the 30° angle. Is the right-side view really needed? LOCATER 2.12 l.O0 .06 .56 .12 30° 1.56 2.26 2.62 4.76 View here

given the top and right side views, sketch the front view as a full section SECTIONA-A...

given the top and right side views, sketch the front view as a full section SECTIONA-A SECTION B-B SECTION C-C
sketch an isometric view given top front and right views. ㄚ Top, Front & the side...

sketch an isometric view given top front and right views. ㄚ Top, Front & the side views are given. Sketch an isometric view.
Isometric & Oblique 1. Given the front, top and right side views of the object, sketch...

Isometric & Oblique 1. Given the front, top and right side views of the object, sketch the Isometric pictorial of the object. You may use isometric grid paper if desired. Keep the object in proportion. TOP Zoo FRONT RIGHT SIDE 2. Given the front and top views of the object, sketch the Oblique Cavalier pictorial of the object on Engineering paper at 30 degrees. Keep the object in proportion. - - ТОР FRONT

STUDENT NUMBER Front, top, and left side views of the object are given. Sketch an isometric...

STUDENT NUMBER Front, top, and left side views of the object are given. Sketch an isometric view of the object. This view must show the object as seen in the direction of the arrow. Draw using I I scale.
Given: The front and top views of an object. Required: Draw the right side view and...

Given: The front and top views of an object. Required: Draw the right side view and complete the bottom half as instructed. For part 2: Draw the right side view of surface 14,17,19,20,26. ORTHOGRAPHIC READING GIVEN: The front and top views of an object. 10 REQUIRED: Draw the right side view and complete the bottom half as instructed. 13 14 15 16 17 18. 26 20 22 Draw the right side view of surface 14,17,19,20,26. 14 26
Given the front and left side use 45 angle projection and draw the top view. then complete anothe...

given the front and left side use 45 angle projection and draw the top view. then complete another 3 orthographic views by first drawing the front view revolved clockwise on A as a pivot until milled slot is horizontal for cutting on a milling machine, then project top and left side. dimension all views. Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50 Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50

2. Draw multiviews below (here they are top, front and right side views) as front, top...

2. Draw multiviews below (here they are top, front and right side views) as front, top and left-side view and add mising lines. Use red pencil for missing lines. And please watch the video named missing lines) that I uploaded on Ims for help. the missing line EXAMPLE 1 Soun 986622ELA DUOLE