Homework Answers
Add Answer to:
7. (15 Points) A standard steel specimen having a diameter of 0.505 in and a 2.00-in,...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in)...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in) of 4140 steel with 2 inch initial gage length (Lo 2.00 in), and the following were determined: . Elastic Modulus (E)-30 x 106 psi Yield Strength (To) = 60,000 psi Strain at maximum load = 0.15 .Breaking Load (Pbreak) 15,000 lbs Maximum Load (Pa) 20,000 lbs 0 % Elongation-25% . a. (3 points) Calculate the stress at the break point: b. (5 points) Calculate...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
Need ASAP, Show all steps. Thanks. Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
A steel cable with a yield strength of 35 ksi is used to support a load...
A steel cable with a yield strength of 35 ksi is used to support a load of 10000 lb. Select the diameter of the cable using a factor of safety of 2.5. A standard steel specimen having a diameter of 0.502 in, and a gauge length of 2.00 in is used in a tension test. At 6000 lb the deformation is recorded as 0.00212 in. The load at the yield point is 7130 lb and the ultimate load is 11520...
Problem 1: A tension test was performed on a steel specimen having an original diameter of...
Problem 1: A tension test was performed on a steel specimen having an original diameter of 0.50 in. and gage length of 2.00 in. The final diameter is de .38 in. The data is listed in the table. 1) Plot the stress-strain diagram on engineering paper, so you can calculate the area easily; 2) Determine approximately the modulus of elasticity; 3) Find the yield stress by 0.2% offset method; 4) Calculate approximately the modulus of resilience; 5) Determine approximately the...
please be very 100% sure before doing. thank you (1) (25 points) Load-elongation dataset were obtained...
please be very 100% sure
before doing. thank you
(1) (25 points) Load-elongation dataset were obtained from a tensile test of high-strength steel as shown in the table. The test specimen had a diameter of 0.505 in. and a gage length of 2.00 in. The Poisson's ratio of high-strength steel is found to be 0.33 At fracture, the elongation between the gage marks was 0.12 in and the minimum diameter was 0.42 in 1) Plot the engineering stress-strain curve using...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
please solve #7. 6. A tension test specimen of a certain material has a diameter of...
please solve #7.
6. A tension test specimen of a certain material has a diameter of 0.5 in and gage marks set 2 in The load versus deflection results of a tension test are shown below where p = 16,000 lb and 0.007 in. Young's modulus for the material is best given by a 23.3 x 10 psi d=0.5in b. 5.82 x 10 psi 2.29 x 10psi d. 73.1 x 10º psi P] Fractures 56 38 672 7. The modulus...
Question 15 15 pts A tensile test specimen has a 2.088"gage length and 0.905" diameter. Yield...
Question 15 15 pts A tensile test specimen has a 2.088"gage length and 0.905" diameter. Yield occurs at a load of 27.808.7 lb wherein the specimen gage is 83.0 10-4"longer. This is an 0.2 percent yield point. Young's Modulus is __psi. Question 16 15 pts A tensile test specimen has a 2.0 in. gage length and 0.875 in. diameter. Yield occurs at a load of 31,000.0 lb wherein the specimen gage is 83.0 10-4 in longer. This is an 0.2...
Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it
1. Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it. Provide a one-two sentence explanation for each point and region along the diagram. 2. A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa (30 x 10* psi) and an original diameter of 10.2 mm (0.40 In.) will experience only elastic deformation when a tensile load of 8900 N (2000 Ibe) is applied. Compute the maximum length...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in) of 4140 steel with 2 inch initial gage length (Lo 2.00 in), and the following were determined: . Elastic Modulus (E)-30 x 106 psi Yield Strength (To) = 60,000 psi Strain at maximum load = 0.15 .Breaking Load (Pbreak) 15,000 lbs Maximum Load (Pa) 20,000 lbs 0 % Elongation-25% . a. (3 points) Calculate the stress at the break point: b. (5 points) Calculate...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
A steel cable with a yield strength of 35 ksi is used to support a load of 10000 lb. Select the diameter of the cable using a factor of safety of 2.5. A standard steel specimen having a diameter of 0.502 in, and a gauge length of 2.00 in is used in a tension test. At 6000 lb the deformation is recorded as 0.00212 in. The load at the yield point is 7130 lb and the ultimate load is 11520...
Problem 1: A tension test was performed on a steel specimen having an original diameter of 0.50 in. and gage length of 2.00 in. The final diameter is de .38 in. The data is listed in the table. 1) Plot the stress-strain diagram on engineering paper, so you can calculate the area easily; 2) Determine approximately the modulus of elasticity; 3) Find the yield stress by 0.2% offset method; 4) Calculate approximately the modulus of resilience; 5) Determine approximately the...
please be very 100% sure
before doing. thank you
(1) (25 points) Load-elongation dataset were obtained from a tensile test of high-strength steel as shown in the table. The test specimen had a diameter of 0.505 in. and a gage length of 2.00 in. The Poisson's ratio of high-strength steel is found to be 0.33 At fracture, the elongation between the gage marks was 0.12 in and the minimum diameter was 0.42 in 1) Plot the engineering stress-strain curve using...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
please solve #7.
6. A tension test specimen of a certain material has a diameter of 0.5 in and gage marks set 2 in The load versus deflection results of a tension test are shown below where p = 16,000 lb and 0.007 in. Young's modulus for the material is best given by a 23.3 x 10 psi d=0.5in b. 5.82 x 10 psi 2.29 x 10psi d. 73.1 x 10º psi P] Fractures 56 38 672 7. The modulus...
Question 15 15 pts A tensile test specimen has a 2.088"gage length and 0.905" diameter. Yield occurs at a load of 27.808.7 lb wherein the specimen gage is 83.0 10-4"longer. This is an 0.2 percent yield point. Young's Modulus is __psi. Question 16 15 pts A tensile test specimen has a 2.0 in. gage length and 0.875 in. diameter. Yield occurs at a load of 31,000.0 lb wherein the specimen gage is 83.0 10-4 in longer. This is an 0.2...
Most questions answered within 3 hours.
-
Garcia Company issues 20.00%, 15-year bonds with a par value of
$470,000 and semiannual interest payments....
asked 2 minutes ago -
The price of 1 lb of potatoes is $1.75. If all the potatoes sold
today at...
asked 4 minutes ago -
In C++ Programming, Try using loops only.
This lab demonstrates the use of the While Loop...
asked 51 minutes ago -
Effect of DCMU and sodium azide on Chlamydomonas? We did an
experiment where we had Chlamydomonas...
asked 1 hour ago -
1a) According to the ideal gas law, _______________.
a. a gas has infinite volume at absolute...
asked 3 hours ago -
Oakdale Fashions, Inc. had $245,000 in 2018 taxable income.
Using the tax schedule in Table 2.3...
asked 3 hours ago -
The marketing class at CSUS had an average score of 150. An
educational analyst determined that...
asked 4 hours ago -
Justin Case has purchased a $250 000 home by putting 20 % down
and taking out...
asked 4 hours ago -
1. In a labor market, marginal cost for a firm is
____________.
a. recruiting cost
b....
asked 5 hours ago -
On January 1, 2019, ABC Company issued $60,000,000 of 20-year,
10.5% bonds when the market rate...
asked 5 hours ago -
39.4% of US homes continue to use a landline in addition to cell
phone service. 3...
asked 6 hours ago -
Starting with benzene, synthesize 1-phenyl-1-butyne.
Show intermediates and reagents.
asked 7 hours ago