Homework Answers
Add Answer to:
Question 15 15 pts A tensile test specimen has a 2.088"gage length and 0.905" diameter. Yield...
A test specimen in a tensile test has a gage length of 2.0 in and an area 0.5 in". During the test the Specimen...
A test specimen in a tensile test has a gage length of 2.0 in and an area 0.5 in". During the test the Specimen yields strength of the material 64,000 lb/in . The corresponding gage length a 2.0083 in. This is the 0.2 percent yield point. The tensile strength of material 120,000 Ib/in? is reached at a gage length 2.60 in. Determine (a) load at yield point, (b) modulus of elasticity, and (c) maximum load. (d) At the point of...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
A tensile test specimen has a gage length = 50 mm and diameter = 20 mm....
A tensile test specimen has a gage length = 50 mm and diameter = 20 mm. Yielding occurs at a load of 137900. The corresponding gage length = 51 mm, which is the 0.2 percent yield point. The maximum load of 258100 N is reached at a gage length = 62.8 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength.
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in)...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in) of 4140 steel with 2 inch initial gage length (Lo 2.00 in), and the following were determined: . Elastic Modulus (E)-30 x 106 psi Yield Strength (To) = 60,000 psi Strain at maximum load = 0.15 .Breaking Load (Pbreak) 15,000 lbs Maximum Load (Pa) 20,000 lbs 0 % Elongation-25% . a. (3 points) Calculate the stress at the break point: b. (5 points) Calculate...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
Given the following data from a tensile test. Show your calculations for the following: Tensile Stress...
Given the following data from a tensile test. Show your
calculations for the following:
Tensile Stress
Modulus of Elasticity (Young’s Modulus)
Yield Strength
Percentage of elongation
Percentage of reduction in area
The following data were collected from a 12-mm-diameter test specimen of magnesium (l. = 30.00 mm): 250 Vielding 0.2% offset Load (N) 0 5,000 10,000 15,000 20,000 25,000 26,500 27,000 26,500 25,000 Gage Length (mm) 0.0000 0.0296 0.0592 0.0888 0.15 0.51 0.90 1.50 (maximum load) 2.10 Stress (MPa) oro...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The load-length data are recorded during the test and are tabulated below. After fracture, the diameter of the specimen near the fracture point was 9.5 mm. Load (N) 7,330 15,100 23,100 30,400 34,400 38,400 41,300 44.800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 Length (mm) 50.800 50.851 50.902 50.952 51.003 51.054 51.308 51.816 52.832...
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test...
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test results shown in Figure 2. The specimen fracture. Using these results, determine the following: Young's Modulus (3 points). The Yield Stress at 0.2% offset (3 points). The Ultimate Tensile Stress (1 point). The percent elongation at failure (1 point). • The toughness of the material (2 points). --- - -- Stress (o) (MPa) 0.04 0.035 0 0.045 0 0.005 0.01 0.015 0.02 0.025 0.03...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length...
1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length of 50 mm wa. tested to fracture. The stress-strain curve from the tension test is shown below. Labeling your points and showing the necessary steps, along with the corresponding calculations, find the following magnitudes: (a) Modulus of Elasticity, E = (b) Ultimate Strength = (e) Yield stress (0.2% offset method), (d) If the shear modulus of elasticity of the material is 28 GPa, determine...
A test specimen in a tensile test has a gage length of 2.0 in and an area 0.5 in". During the test the Specimen yields strength of the material 64,000 lb/in . The corresponding gage length a 2.0083 in. This is the 0.2 percent yield point. The tensile strength of material 120,000 Ib/in? is reached at a gage length 2.60 in. Determine (a) load at yield point, (b) modulus of elasticity, and (c) maximum load. (d) At the point of...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in) of 4140 steel with 2 inch initial gage length (Lo 2.00 in), and the following were determined: . Elastic Modulus (E)-30 x 106 psi Yield Strength (To) = 60,000 psi Strain at maximum load = 0.15 .Breaking Load (Pbreak) 15,000 lbs Maximum Load (Pa) 20,000 lbs 0 % Elongation-25% . a. (3 points) Calculate the stress at the break point: b. (5 points) Calculate...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
Given the following data from a tensile test. Show your
calculations for the following:
Tensile Stress
Modulus of Elasticity (Young’s Modulus)
Yield Strength
Percentage of elongation
Percentage of reduction in area
The following data were collected from a 12-mm-diameter test specimen of magnesium (l. = 30.00 mm): 250 Vielding 0.2% offset Load (N) 0 5,000 10,000 15,000 20,000 25,000 26,500 27,000 26,500 25,000 Gage Length (mm) 0.0000 0.0296 0.0592 0.0888 0.15 0.51 0.90 1.50 (maximum load) 2.10 Stress (MPa) oro...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The load-length data are recorded during the test and are tabulated below. After fracture, the diameter of the specimen near the fracture point was 9.5 mm. Load (N) 7,330 15,100 23,100 30,400 34,400 38,400 41,300 44.800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 Length (mm) 50.800 50.851 50.902 50.952 51.003 51.054 51.308 51.816 52.832...
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test results shown in Figure 2. The specimen fracture. Using these results, determine the following: Young's Modulus (3 points). The Yield Stress at 0.2% offset (3 points). The Ultimate Tensile Stress (1 point). The percent elongation at failure (1 point). • The toughness of the material (2 points). --- - -- Stress (o) (MPa) 0.04 0.035 0 0.045 0 0.005 0.01 0.015 0.02 0.025 0.03...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length of 50 mm wa. tested to fracture. The stress-strain curve from the tension test is shown below. Labeling your points and showing the necessary steps, along with the corresponding calculations, find the following magnitudes: (a) Modulus of Elasticity, E = (b) Ultimate Strength = (e) Yield stress (0.2% offset method), (d) If the shear modulus of elasticity of the material is 28 GPa, determine...
Most questions answered within 3 hours.
-
At the beginning of the period, the Fabricating Department
budgeted direct labor of $136,500 and equipment...
asked 9 minutes ago -
Please answer all
____ 28. Rent control is usually
justified on the grounds that it protects...
asked 9 minutes ago -
PARTS A-D HAVE BEEN ANSWERED. WAS TOLD TO REPOST. ONLY ANSWER
PARTS E and F.
A...
asked 27 minutes ago -
2) You are given the task of finding a representation for a
circle in a drawing...
asked 1 hour ago -
STUDY QUESTION: Does use of diet drug fen-phen
(fenfluramine-phentermine) cause valvular heart disease?
HINT: Valvular heart...
asked 1 hour ago -
1. An object weighing 40 N rests on a surface. The coefficient
of friction is 0.35....
asked 2 hours ago -
Investor company owns 35% of investee company voting stock and
accounts for the investment under the...
asked 3 hours ago -
The number of major faults on a randomly chosen 1 km stretch of
highway has a...
asked 4 hours ago -
Consider the competitive environment of Starbuck's, Progressive
Insurance, a manufacturing firm with low turnover, or a...
asked 4 hours ago -
3. Gains from trade
Consider two neighbouring island countries called Euphoria and
Contente. They each have...
asked 6 hours ago -
A business executive has the option to invest money in two
plans: Plan A guarantees that...
asked 9 hours ago -
Hello, can someone please help me answer this question?
How much heat is absorbed by a...
asked 9 hours ago