Homework Answers
Add Answer to:
1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length...
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test...
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test results shown in Figure 2. The specimen fracture. Using these results, determine the following: Young's Modulus (3 points). The Yield Stress at 0.2% offset (3 points). The Ultimate Tensile Stress (1 point). The percent elongation at failure (1 point). • The toughness of the material (2 points). --- - -- Stress (o) (MPa) 0.04 0.035 0 0.045 0 0.005 0.01 0.015 0.02 0.025 0.03...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
Given the following data from a tensile test. Show your calculations for the following: Tensile Stress...
Given the following data from a tensile test. Show your
calculations for the following:
Tensile Stress
Modulus of Elasticity (Young’s Modulus)
Yield Strength
Percentage of elongation
Percentage of reduction in area
The following data were collected from a 12-mm-diameter test specimen of magnesium (l. = 30.00 mm): 250 Vielding 0.2% offset Load (N) 0 5,000 10,000 15,000 20,000 25,000 26,500 27,000 26,500 25,000 Gage Length (mm) 0.0000 0.0296 0.0592 0.0888 0.15 0.51 0.90 1.50 (maximum load) 2.10 Stress (MPa) oro...
(c) Acylindrical specimen of stainless steel having a diameter of 12.8 mm and a gauge length...
(c) Acylindrical specimen of stainless steel having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The data acquired was used to plot engineering stress versus engineering strain as shown in the following two graphs (please note that fig. b is a blown-up clastic portion of (a)). Use the o-curves to complete parts through (vi) Stress (MP) 0.00 0.02 0.04 0.06 0.08 0.10 Strain Fig (a). - curve of stainless steel Stress (MPa)...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
Calculate The modulus of resilience The tensile strength The reduction in area The elongation The engineering...
Calculate
The modulus of resilience
The tensile strength
The reduction in area
The elongation
The engineering stress at fracturg
The modulus of elasticity
The 0.2 offset strength
Problem The following data were collected from a standard 12 mm diameter test specimen of a magnesium alloy (initial :length( Lo = 30.0mm) 20000 15000 10000 5000 0.0 Load (N) 26500 25000 27000 26500 25000 0.15 0.09 0.06 0.03 0.0 AL (mm) 2.10 2.79 1.50 0.90 0.51 After fracture, the total length was...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The load-length data are recorded during the test and are tabulated below. After fracture, the diameter of the specimen near the fracture point was 9.5 mm. Load (N) 7,330 15,100 23,100 30,400 34,400 38,400 41,300 44.800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 Length (mm) 50.800 50.851 50.902 50.952 51.003 51.054 51.308 51.816 52.832...
3) A tensile test is performed on a brass specimen 10 mm in diameter and a...
3) A tensile test is performed on a brass specimen 10 mm in diameter and a length of 50 mm. When the tensile load reaches 20 kN, the material elongates 0.122 mm. What is the brass' modulus of elasticity E?
A tensile test specimen has a gage length = 50 mm and diameter = 20 mm....
A tensile test specimen has a gage length = 50 mm and diameter = 20 mm. Yielding occurs at a load of 137900. The corresponding gage length = 51 mm, which is the 0.2 percent yield point. The maximum load of 258100 N is reached at a gage length = 62.8 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength.
1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test results shown in Figure 2. The specimen fracture. Using these results, determine the following: Young's Modulus (3 points). The Yield Stress at 0.2% offset (3 points). The Ultimate Tensile Stress (1 point). The percent elongation at failure (1 point). • The toughness of the material (2 points). --- - -- Stress (o) (MPa) 0.04 0.035 0 0.045 0 0.005 0.01 0.015 0.02 0.025 0.03...
PROBLEM5 A tensile test specimen of stainless steel alloy having a diameter of 0.495 inches and a gage length of 2.00 in was tested to fracture. Stress and strain data obtained during the test are shown below. Determine a. The modulus of elasticity b. The proportional limit c. the ultimate strength d, the yield strength (with a 0.20% offset) 160 Upper scale 120 Lower scale 40 0.0 0.020 0.040 0.060 0.080 0.100 0.120 L-Le 0.0 0.002 0.004 0.006 0.008 0.010...
Given the following data from a tensile test. Show your
calculations for the following:
Tensile Stress
Modulus of Elasticity (Young’s Modulus)
Yield Strength
Percentage of elongation
Percentage of reduction in area
The following data were collected from a 12-mm-diameter test specimen of magnesium (l. = 30.00 mm): 250 Vielding 0.2% offset Load (N) 0 5,000 10,000 15,000 20,000 25,000 26,500 27,000 26,500 25,000 Gage Length (mm) 0.0000 0.0296 0.0592 0.0888 0.15 0.51 0.90 1.50 (maximum load) 2.10 Stress (MPa) oro...
(c) Acylindrical specimen of stainless steel having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The data acquired was used to plot engineering stress versus engineering strain as shown in the following two graphs (please note that fig. b is a blown-up clastic portion of (a)). Use the o-curves to complete parts through (vi) Stress (MP) 0.00 0.02 0.04 0.06 0.08 0.10 Strain Fig (a). - curve of stainless steel Stress (MPa)...
A Grade 2 Titanium tension test specimen has a diameter of 12.60 mm and a gage length of 50 mm. In a test to fracture, load and deformation data obtained during the test are given in the accompanying table. Plot the stress strain relationship then, determine the following: (a) the modulus of elasticity. (b) the proportional limit. (c) the yield strength (0.20% offset). (d) the ultimate strength. (e) the fracture stress. (f) the true fracture stress if the final diameter...
Calculate
The modulus of resilience
The tensile strength
The reduction in area
The elongation
The engineering stress at fracturg
The modulus of elasticity
The 0.2 offset strength
Problem The following data were collected from a standard 12 mm diameter test specimen of a magnesium alloy (initial :length( Lo = 30.0mm) 20000 15000 10000 5000 0.0 Load (N) 26500 25000 27000 26500 25000 0.15 0.09 0.06 0.03 0.0 AL (mm) 2.10 2.79 1.50 0.90 0.51 After fracture, the total length was...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The load-length data are recorded during the test and are tabulated below. After fracture, the diameter of the specimen near the fracture point was 9.5 mm. Load (N) 7,330 15,100 23,100 30,400 34,400 38,400 41,300 44.800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 Length (mm) 50.800 50.851 50.902 50.952 51.003 51.054 51.308 51.816 52.832...
3) A tensile test is performed on a brass specimen 10 mm in diameter and a length of 50 mm. When the tensile load reaches 20 kN, the material elongates 0.122 mm. What is the brass' modulus of elasticity E?
Most questions answered within 3 hours.
-
Suppose X follows an exponential distribution with mean 7.5.
Determine the conditional probability P(x > 2.5...
asked 13 minutes ago -
Young softball batters are often instructed to “choke-up on the
bat” by their coach. In terms...
asked 16 minutes ago -
Suppose that you are an official with Mexico's economic
development agency. Write a one-page memo detailing...
asked 47 minutes ago -
If you were an international firm, why would you support the
concept of global free trade?...
asked 1 hour ago -
Cisco packet tracer
Q1) Do you get any changes of IP address when packet is
traversing...
asked 1 hour ago -
What is the pressure inside a 33.0 L container holding 106.4 kg
of argon gas at...
asked 2 hours ago -
Question no 2
A housekeeping support department budgets its costs at
SR 40,000 per month plus...
asked 2 hours ago -
A 1400Kg sports car accelerates from rest to 90km/h in 7.0s.
What is the average power...
asked 3 hours ago -
For the following reaction, 0.128 moles of
potassium hydrogen sulfateare mixed with
0.504 moles of potassium...
asked 6 hours ago -
1. What is the present value of $400, three years in the future
if the interest...
asked 7 hours ago -
The labor force minus the number of employed equals the number
of unemployed.
a. True
b....
asked 9 hours ago -
Determine the mass in units of grams [g] of 0.49 moles [mol]
of a new fictitious...
asked 9 hours ago