Q1. The bar has a diameter of 50 mm. If it is subjected to a force...
The bar has a diameter of 40 mm. If it is subjected to a force of 800N as shown figure, determine the stress components that act at point A and B. 150 mm 200 mm 30 800N
Figure 2: The bar has a diameter of 40 mm. Determine the state of stress at point B and show the results on a differential volume element located at this point Determine the shear stress (T.xy) B? 16.2 MPa O 0.509 MPa -0.679 (MPa Figure 2 200 mm Y 200 mm AB 1200 N* 1200 N 800 N The bar has a diameter of 40 mm. Determine the state of stress at point B and show the results on a...
A L-Shaped solid bar of 50-mm diameter is subjected to a 13 kN force as shown below. At point H (a)Determine the state of stresses and show the results on a stress-element. (b)Determine the Principal stresses, the principal planes and the maximum shear stress
e bar has a diameter of 40 mm. Determine the ress at point A and show the results on a tial volume element located at this point. Solve Prob. 8-68 for point B. differential 9. 200 mm y 200 mm A 1200 N 2 4 800 N Probs. 8-68/69
7 of 15 6-of-9 Problem 4 (35 Points) The rod has a diameter of 40 mm. It is subjected to the force and moment system shown. (a) (15 points) Determine the stress components that act at point B. Show the results on a volume element below located at this point. (b) (10 points) Assume that the stress components at point A are given by Ox = -37 MPa, y = 0 MPa, Try = - 8 MPa. Draw a Mohr's...
X The bar has a diameter of 47.8 mm. If it is subjected to the loadings shown (P = 755 N, T = 56.5 Nm, L1 = 200 mm, and L2 = 100 mm, determine the shear stress in MPa) at point A. Note: Your answer should include requested units and be to 3 decimal places. L2 11 A B X 30° Selected Answer: [None Given] Correct Answer: 3.121 + 2% (MPa)
X The bar has a diameter of 46.2 mm. If it is subjected to the loadings shown (P = 685 N, T = 39.3 Nm, L1 = 299 mm, and L2 = 220 mm, determine the normal stress (in MPa) at point B. Note: Your answer should include requested units and be to 3 decimal places. L2 L1 A B X 30° Selected Answer: [None Given) Correct Answer: -18.117 2% (MPa)
Combined loading A rod with the diameter of 20 mm is subjected to a force P - 1800 N, as shown in the figure. The rod is fixed to the wall at Point C.L.- 50 mm and L-200 mm. Determine the magnitude of the shear stress MPa at Point Blocated on the surface of the rod on the designated positive z axis (rounding to two decimal places).
*8-56. The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B, and show the results on a differential volume element located at this point.
Q1. A circular rod of 12 mm diameter was tested for tension. The total elongation on a 300 mm length was 0.22 mm under a tensile load of 17 KN. Find the value of E. (2.5 Marks) Answer: Q2. A prismatic bar has a cross section of 25 mm x 50 mm and a length of 2m under an axial force of 90 KN. The measured elongation of the bar is 1.5 mm. Compute the tensile stress and strain in...