1)
first, draw a k map
The map layout should be like this
Then using the A,B,C,D just place the ONES at the that suitable positions
here is the map-
HERE ONLY ONE GROUP IS POSSIBLE THAT IS (0,2,8,10)
i
Find the minimized version of the circuit using a Kmap: ABCD' + A'B'CD' + AB'CD +...
Q2. Draw the nominal π circuit that is used to represent the medium-length transmission line model with total series impedance Z and total shunt admittance Y. Then derive the equations to express the ABCD parameters (a) 20% (b)A 200 km, 230 kV, 50 Hz three-phase overhead transmission line has a positive-sequence series impedance z (0.08 + j0.48) Ω/km, and a positive-sequence shunt admittance y-j3.33 x 10T° S/km. At full load, the line delivers 250 MW at 0.99 power factor lagging...
5) Decoders: Given the following circuit, S0 and S1 are computed using a 4-2 priority encoder with the priorities indicated on the figure. (hint: IDLE signal is always 0, if any of the inputs 10,11,12, or 13 is 1) 6 points) 4-to-2 Priority Encoder 10 YO YI 13 IDLE 13> 11 > 12>10 12 Full c Adder So Fill the following table showing the output signals S0 and SI given the input signals w, x, y, a) and z. Prof...
For the FET amplifier of Fig. 1, using identical FET transistors as shown in the circuit, answer the following: 1- How many stages do we have in this system and what is the name for each one? 2- For each stage draw tranfer curve in details. 3- For each stage find working point (DC analysis) 4- For each stage draw equalivent ac circuit. 5- For each stage calculate: Av, Zi, Zo 6- Calculate overall gain of the amplifier 7- Calculate...
PROBLEM STATEMENT The mini-calculator will use a small ALU to perform arithmetic operations on two 4-bit values which are set using switches. The ALU operations described below are implemented with an Adder/Subtractor component. A pushbutton input allows the current arithmetic result to be saved. An upgraded mini-calculator allows the saved value to be used in place of B as one of the operands. The small ALU that you will design will use the 4-bit adder myadder4 to do several possible...
Find the equation of the line using the point-slopa formula. Write the final aquation using the slope-intercopt form the x-intercept is 1, and (x, y) (-2, 3) is a point on the line Recall that the point-slope formula for a line is of the form - yi - m(x-x1). What are the coordinates of the point for the givenx-intercept? Can the slope of the line be found using the two points? What variab be solvad for in order to convert...
can you please help me with number 2 and 3? thanks Problem 2. Consider a version of question 9 from the first WebWork problem set and an attempt at solving it. Find and explain the 3 mistakes that were made. Use the line numbers to identify where they occurred. Question 9: If a (base 10) double-log plot displays a line through the points (-3, -2) and (5,5), find the relation between x and y. Solution attempt: First, a correct double-log...
Example 28.12 Charging a Capacitor in an RC Circuit Problem An uncharged capacitor and a resistor are battery, as shown in Figure 28.23. If emf = 12.0 V, C = 5.00 AuF, and R = 8.00 x 105 ?, find the time constant of the circuit, the maximum charge on the capacitor, and the charge and current as functions of time. in series to a Figure 28.23 The switch in this series RC circuit, open for times t> , is...
Vss (b) Find ( Drav amp the variation of D 7.103 Figure P7.103 feedback-bias circuit of Fig. 7.50. Using a 5-V supply with an NMOS transistor for which V, =0.8 V, k. = 8 mA/V =0, provide a design that biases the transistor at I = 1 nA, with Vps large enough to allow saturation operation for a 2-V negative signal swing at the drain. Use 22 MS2 as the largest resistor in the feedback-bias network. What values of R...
solve # 3 only using math lab The following is a wind gradient data taken in city environment with high rise buildings: 1. Height from ground (m): 0,50, 100, 150, 200, 250, 300, 350, 400, 450, 500 Wind Speed (m/s) 0,7, 15, 23, 30, 33, 35, 37, 42, 50, 60 Using mat lab, (i) do a line plot of wind speed against height. (ii) Repeat above for bar plot. The following is the wind speed and power density data for...
Do: Find the Laplace transform, F(s), for each f(t) given below in parts a) and b). Express F(s) polynomials ins where the denominator polynomial, A(s) Le., it has the value "1" (one) Monic Rational Form (MRF). This means that the result is a ratio of polynomials, and the coefficient, a, in the denominator polynomial, A(s) below is a, 1 as a ratio of =s"+a-1s"- + a28 +a1s +a0, is monic as the leading coefficient on the highest power of s....