Homework Answers
Add Answer to:
QUESTION 1 A double riveted double cover butt joint in plates 24 mm thick is made...
A triple riveted butt joint with equal double cover plates (zig-zag riveting) is used for the...
A triple riveted butt joint with equal double cover plates (zig-zag riveting) is used for the longitudinal joint of a Lancashire boiler of 2.5 m internal diameter. The working steam pressure is 1.12 N/mm2 and the efficiency of the joint is 85 per cent. Calculate the plate thickness for mild steel of 460 MPa ultimate tensile strength. Assume ratio of tensile to shear stresses as 7/6 and factor of safety 4. The resistance of the rivets in double shear is...
Three plates are joined with a 12 mm diameter pin as shown. Determine the maximum load P that can be transmitted by the joint if:(a)The maximum normal stress on a cross-section of the plates at the pin must not exceed 372 MPa.(b)The maximum bearing stress
Three plates are joined with a 12 mm diameter pin as shown. Determine the maximum load P that can be transmitted by the joint if:(a)The maximum normal stress on a cross-section of the plates at the pin must not exceed 372 MPa.(b)The maximum bearing stress between a plate and the pin must not exceed 612 MPa.(c)The maximum shear stress on a cross-section of the pin must not exceed 268 MPa.(d)The punching shear resistance of the material in the top and...
assume: width (mm)= 30 overlap (mm)= 21 glue strength (n/mm^2)= 1 3. See the double lap joint shown below. Assume that...
assume:
width (mm)= 30
overlap (mm)= 21
glue strength (n/mm^2)= 1
3. See the double lap joint shown below. Assume that the plates at the joint are connected using an epoxy having a shear strength between 1.0 and 2.5 N/mm2 and the entire overlap is glued. a. Given the width of the plates and length of overlap from the spreadsheet, what is the shear stress in the epoxy? b. What is the minimum area of overlap given the strength of...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter of d) in Plate A. It is assumed that weld failure will not occur (a) If Plate A has a yield stress (fy) of 350 MPa and an ultimate tensile strength (fu) of 450 MPa, what is the maximum load (P)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
assume:
width (mm)= 30
overlap (mm)= 21
glue strength (n/mm^2)= 1
3. See the double lap joint shown below. Assume that the plates at the joint are connected using an epoxy having a shear strength between 1.0 and 2.5 N/mm2 and the entire overlap is glued. a. Given the width of the plates and length of overlap from the spreadsheet, what is the shear stress in the epoxy? b. What is the minimum area of overlap given the strength of...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter of d) in Plate A. It is assumed that weld failure will not occur (a) If Plate A has a yield stress (fy) of 350 MPa and an ultimate tensile strength (fu) of 450 MPa, what is the maximum load (P)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
Most questions answered within 3 hours.
-
what is the maximum number of pair electron-positron a 2 MeV photon
can produce
asked 1 minute ago -
Discuss the mechanisms your body uses to maintain normal water
and temperature balance. This answer should...
asked 11 minutes ago -
Given two polynomials equation, write a function that
adds and multiply the given two
polynomials.
It...
asked 23 minutes ago -
Implement the Unsorted, sorted and indexed lists using Linked
List base structure. (LLNode class under support...
asked 25 minutes ago -
Exercise 5-21 Income (loss) recognition; Long-term contract;
revenue recognition over time vs. upon project completion
[LO5-9]...
asked 28 minutes ago -
A rich aunt has promised you $2,090.00, one year from today. In
addition, each year after...
asked 28 minutes ago -
Data from the past shows that on average, a ready-mixed concrete
plant receives 100 orders for...
asked 1 hour ago -
The table below shows the number of state-registered automatic
weapons and the murder rate for several...
asked 1 hour ago -
Container A holds 762 mL of ideal gas at 2.60 atm. Container B
holds 144 mL...
asked 1 hour ago -
1)
Why is bulk transport necessary in both plants and animals?
The premise of the question...
asked 1 hour ago -
What is the result of the following in MongoDB?
>use MovieDB
>db.movies.find( { genre: { $ne:...
asked 1 hour ago -
What is the NPV?
r=9.28
c1= 5.853
c2= 6.37 + 1,826.76
asked 1 hour ago