A utility hook was formed from a round rod of diameter d = 16 mm into the geometry shown in the figure. Given: F = 5 kN, L = 200 mm, and Di = 60 mm.
a)What is the stress at the inner surface at section
A–A? kN/mm^2
b) What is the stress at the outer surface is determined to be? kN/mm^2
Homework Answers
Add Answer to:
A utility hook was formed from a round rod of diameter d = 16 mm
into...
The 50-mm-diameter metal rod in Figure 3 is rigidly fixed into a wall at A and...
The 50-mm-diameter metal rod in Figure 3 is rigidly fixed into a wall at A and it loaded at its free end as shown. Determine the state of stress, (ox and try), at point P which is on the front surface of the rod. (24 Points) 300 mm А P. N 2 kN GK у 20 KN 0.3 kNm 30 KN z Р Figure 3
The d-diameter rod and t-thick round disk in the figure are prepared in one piece. The...
The d-diameter rod and t-thick round disk in the
figure are prepared in one piece.
The place where the rod meets the disk is 40 mm in diameter. When
the axial tensile load of 20 kN is applied to the end of the rod,
what should be the disc thickness (t) and rod diameter (d) to
prevent damage to the disc and the rod? (Damage to the disc and rod
begins at 35 MPa shear stress and 60 MPa normal...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
Combined loading A rod with the diameter of 20 mm is subjected to a force P...
Combined loading A rod with the diameter of 20 mm is subjected to a force P - 1800 N, as shown in the figure. The rod is fixed to the wall at Point C.L.- 50 mm and L-200 mm. Determine the magnitude of the shear stress MPa at Point Blocated on the surface of the rod on the designated positive z axis (rounding to two decimal places).
The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20 mm and outer diameter of 28 mm
The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20 mm and outer diameter of 28 mm. The rod has a diameter of 12 mm. determine the average normal stress at points D and E and represent the stress on a volume element located at each of these points.
P8.054 A 40-mm-diameter steel rod is formed into a machine part with the shape shown. A...
P8.054 A 40-mm-diameter steel rod is formed into a machine part with the shape shown. A load of P = 3.1 kN is applied to the ends of the part. If the allowable normal stress is limited to 47 MPa, what is the maximum eccentricity e that may be used for the part? Answer: @max = mm the tolerance is +/-2% Click if you would like to Show Work for this question: Open Show Work
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm...
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, determine the normal and shearing stresses at point H on the outer surface. The properties at the cross section at H include: A 1052.4 mm2,J 1,187,700 mm4, 1 593,840 mm4, and QNA 11,243 mm3 3 kN 9 kN 120 mm 150 mm 120 mm a.) Normal stress at H: b.) Shear...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P - 150 kN. Given the yield stress, Oy -250 MPa and factor of safety, F.S. - 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P = 150 kN. Given the yield stress, Oy=250 MPa and factor of safety, F.S. = 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of the...
The 50-mm-diameter metal rod in Figure 3 is rigidly fixed into a wall at A and it loaded at its free end as shown. Determine the state of stress, (ox and try), at point P which is on the front surface of the rod. (24 Points) 300 mm А P. N 2 kN GK у 20 KN 0.3 kNm 30 KN z Р Figure 3
The d-diameter rod and t-thick round disk in the
figure are prepared in one piece.
The place where the rod meets the disk is 40 mm in diameter. When
the axial tensile load of 20 kN is applied to the end of the rod,
what should be the disc thickness (t) and rod diameter (d) to
prevent damage to the disc and the rod? (Damage to the disc and rod
begins at 35 MPa shear stress and 60 MPa normal...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
Combined loading A rod with the diameter of 20 mm is subjected to a force P - 1800 N, as shown in the figure. The rod is fixed to the wall at Point C.L.- 50 mm and L-200 mm. Determine the magnitude of the shear stress MPa at Point Blocated on the surface of the rod on the designated positive z axis (rounding to two decimal places).
P8.054 A 40-mm-diameter steel rod is formed into a machine part with the shape shown. A load of P = 3.1 kN is applied to the ends of the part. If the allowable normal stress is limited to 47 MPa, what is the maximum eccentricity e that may be used for the part? Answer: @max = mm the tolerance is +/-2% Click if you would like to Show Work for this question: Open Show Work
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, determine the normal and shearing stresses at point H on the outer surface. The properties at the cross section at H include: A 1052.4 mm2,J 1,187,700 mm4, 1 593,840 mm4, and QNA 11,243 mm3 3 kN 9 kN 120 mm 150 mm 120 mm a.) Normal stress at H: b.) Shear...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P - 150 kN. Given the yield stress, Oy -250 MPa and factor of safety, F.S. - 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P = 150 kN. Given the yield stress, Oy=250 MPa and factor of safety, F.S. = 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of the...
Most questions answered within 3 hours.
-
Which of the following is false regarding osmosis and diffusion?
a) A single glycogen molecule will...
asked 36 seconds from now -
20.
A diamond mine is expected to produce regular annual cash flows
of $1 million for...
asked 1 minute ago -
Within the client’s IT system, supplier information is contained
in a supplier master file (SMF). Each...
asked 46 seconds ago -
Explain why sound travels faster in warm air than in cool air.
Suppose the room temperature...
asked 6 minutes ago -
The measured glucose level one hour after having a sugary drink
varies according to the normal...
asked 14 minutes ago -
Mic2 is a gene present on both the X and Y chromosome
of humans. Suppose a...
asked 13 minutes ago -
Consider this balanced chemical equation:
H2O2(aq)+3I−(aq)+2H+(aq)→I3−(aq)+2H2O(l)H2O2(aq)+3I−(aq)+2H+(aq)→I3−(aq)+2H2O(l)
In the first 10.0 seconds of the reaction, the concentration...
asked 16 minutes ago -
A neuropathologist is using a device with a thin circular coil
of current-carrying wire of radius...
asked 20 minutes ago -
A Carnot engine whose low-temperature reservoir is at 18.0°C has
an efficiency of 21.9%. By how...
asked 22 minutes ago -
A carpenter is making doors that are 2058.0 millimeters tall. If
the doors are too long...
asked 22 minutes ago -
Suppose you are analyzing a competitor of Levi's Luxury Shop and
determine that Current Assets are...
asked 36 minutes ago -
statistics show
that 40% of adults sleep with socks. Eight adults are randomly
selected
what is...
asked 43 minutes ago