What is the maximum amount of quantization error that can occur in a 10bit system in the input analog voltage is from 0V to 6V?
a) 10mV
b) 6mV
c) 0.5mV
d) 1mV
Answer: b
Explanation: The minimum voltage step input is 6/(2N-1) = 6/1023 =5.865mV ≈6mV. This is the maximum error that can occur during the conversion process.
What is the maximum amount of quantization error that can occur in a 10bit system in the input analog voltage is from 0V to 6V?a) 10mVb) 6mVc) 0.5mVd) 1mV
Oil estion 2 (9%) The voltage output from a J-type thermocouple referenced 0°C is to be used to measure temperatures from 50 to 70°C. The output voltages vary linearly over this range from 2.585 to 3.649 mV 1. If the thermocouple voltage is input to a 12-bit A/D converter having a +5V range, estimate the percent quantization error in the digital value; 2. If the analog signal can be first passed through an amplifier circuit, compute the amplifier gain required...
Problem 2 (25 pts.) A thermocouple is to be used with a 16 bit A/D converter that has an input range of ov to sv. The voltage output of the thermocouple varies linearly with the temperature over the temperature range of 50°C to 70°C; the corresponding voltages at these temperatures are 2.585 mV and 3.649 mV respectively. Parta) 5 pts. Compute the quantization error of the A/D convertor and the temperature resolution for the entire system. Part b) 10 pts....
EXERCISE 4: (30 MARKS) Given the following circuit in figure 3 of a flash analog-to-digital converter where VREF = 2.8V. Op-amp comparators Analog input Priority encoder A A 8. Parallel binary output A A A Sampling A pulses Figure 3 - Circuit of exercise 4 a) Determine the resolution of this converter. b) Determine the maximum error quantization error. c) If the sampling period is 10ms, calculate the number of bits per second bitrate) of the ADC. d) Determine the...
Q2) A unipolar 14 bit ADC measures 0 – 8 volts full scale. a. What is the minimum resolvable voltage (or voltage resolution)? [Hint: resolution decrease as you increase the volts full scale] b. What is the percent quantization error? [Hint: percent quantization error for unipolar 10 bit ADC, 1 V full scale is: (resolution/max voltage) x100% or (975μV/1V) x100% = 0.0975%] c. What is the percent quantization error if a 1 volt max signal is input? [Hint: same resolution...
Communication System Solve with ALL steps Please QUESTION 3 Briefly explain the following Analog Pulse Modulation (APM): (i) Pulse Amplitude Modulation (PAM) Pulse Width Modulation (PWM) (iii) Pulse Position Modulation (PPM) (2 marks) (2 marks) (2 marks) b) There are several digital modulations techniques used to modulate digital signal. For a binary data 10111011, sketch the output waveform if the following modulator is used: Amplitude Shift Keying (ASK) (2 marks) Frequency Shift Keying(FSK) (2 marks) (iii) Phase Shift Keying (PSK)...
What is the output voltage if the input voltage of a compander with a maximum voltage range of 1 V and a μ of 255 is 0.25?a) 0Vb) 0.25Vc) 0.5Vd) 0.75V
A charge travels from the positive terminal of a 6�-V battery, through a light bulb, and through the battery back to the positive terminal. The total change in voltage experienced by the charge during this journey is A) -1V B)1V C)-6V D)6V E)0V
QUESTION 3 (25 MARKS) Describe TWO (2) advantages and TWO (2) disadvantages of digital transmission (C01: P01 - 4 marks) b Sampling, quantization and coding are the three processes used to represent an analog signal in digital form. Considering an input signal into an 8-bit Pulse Code Modulation (PCM) system is a 20 Vpp 50-Hz, answer the followings: i. Using appropriate diagram briefly describe TWO (2) basic methods to perform the sampling function. (CO2: PO2 - 2 marks) Determine the...
A bipolar 8 bit ADC measures 0 – 4 volts full scale. a. What is the minimum resolvable voltage? b. What is the percent quantization error? c. What is the percent quantization error if a 1 volt max signal is input?