It is desired to obtain a series of pulses from a sine wave of a frequency of 100kHz and an amplitude of 10 V. The frequency of the pulse train must be 20kHz, and the pulse width must be 10 microsecond. If a window comparator circuit is used for that purpose, the two threshold voltages must be approximately equal to what?
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
It is desired to obtain a series of pulses from a sine wave of a frequency...
A resistor and an inductor are connected in series with a variable frequency sine wave generator. The peak voltage of the power source is 10.0 V. The frequency is set such that the resistor and the inductor have equal peak voltages. What is the peak voltage across the resistor? What phase angle separates the current from the source voltage? Also indicate whether it is the current or the source voltage that leads. a. b. ViVa ㄟ
(A.) Use MATLAB to generate a pulsed sine wave signal having a frequency F-10KHZ and a pulse width of T-.5ms. The pulse repetition time is 1ms (pulse repetition rate is 1000 pulses/sec), i.e., the signal is zero between pulses. Model the signal to start at time t-0 and to end at a time t=Tstop. Use a sample time of .001ms to approximate an analog environment. Display the signal in MATLAB appropriate for an analog signal, first for Tstop 1ms and...
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...
1.) You want to send a "square wave" pulse signal at a frequency
of 60 Hz. What characteristics would this signal have?
2.) You want to set up a flicker fusion stimulus with a duty
cycle of 50%. Lets say you want to set up a stimulus that is a
total of 2 seconds long with a frequency of 1 Hz, 10 Hz, 20 Hz, 40
Hz, 60 Hz, 80 Hz, and 100 Hz. How do you do that? What...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...
Question 2: (10 points) In the full rectifier circuit shown, the input is a sine wave with a frequency of 50 Hz and an amplitude of 6 V. 1 For this circuit, sketch on the figure below the output voltage across the resistor R assuming ideal diodes. Show the time scale on the figure. Sketch also on the same figure a typical output when a capacitor is placed in parallel with the resistor. vou TOU to ts. ti to 0.00...
Choose the incorrect statements about the experiment of the use of oscilloscope. A. A sine wave is shown on the screen. There are six divisions from peak to pee Therefore, we can conclude that the peak-to-peak voltage is six volts. B. For 5 MHz, the shape of the wave which is shown on the screen is inconsistent with the one we observe in lower frequency. Therefore, we must make some mistakes during the experiment. c. In the experiment, the ratio...
20.3.5 Observe and explain Observe the series of sketches at the right. The pulses travel at speed v along the string of length L. Based on your analysis and using these two quantities, decide the time interval T (called the period for the first vibration) between upward pulls of the hand so that each upward pull sup-b. ports or enhances the pulse that has just returned to and reflected from your hand after one trip down the string and back....
An ac series circuit consists of a voltage source of frequency f = 60 Hz and voltage amplitude V, a resistor of resistance R = 593 Ω, and a capacitor of capacitance C = 2.8×10−6F. What must the source voltage amplitude V be for the average electrical power consumed in the resistor to be 382 watts? There is no inductance in the circuit.
Circuit 3-RL High Pass Filter Circuit Choose R=1.5 k Ω, and L=27 mH . Input from AWG is a Sine Wave, 4 V, 500 Hz, Base 2 ms/div, Click on Network Analyzer. Choose start frequency 100 Hz and Stop frequency 100 kHz and steps 100 .Bode scale for Magnitude: Top 0 dB, Range 10 dBBode scale for Phase: Top 90°, Range 75%. (You can always play with the scale. Make sure the Phase and Magnitudo are seen well on the screen)Measure...