Please show all work 3) Given: Bending moment diagrams and cross section, wall thickness = /2...

Question

Question

Please show all work

3) Given: Bending moment diagrams and cross section, wall thickness = /2 in. Solve: The centroid, moment of inertia and the m

Answer 1

Answer #1

21Lb [361 746 125900 My filt ) N -132000 woll Thickness 1/2 unch. centooids s = 294 - Ž = E Bexz 6 in (here 4-6 ca=120 Thenta

Answer 2

Similar Homework Help Questions

50 M=2.0kN.m 100 160 100 Fig. 3 Fig. 4 Prob. 3. For the unsymmetric cross section...

50 M=2.0kN.m 100 160 100 Fig. 3 Fig. 4 Prob. 3. For the unsymmetric cross section shown in Fig. 3, a moment M is applied at +45° from z. All dimensions are in mm. The thickness = 4 mm. Determine (a) the centroid of the cross section (b) the moments of inertia and product of inertia under y-z (c) the principal moments of inertia and the direction of the principal system (d) the orientation of the neutral axis in terms...
Question 3: Two vertical forces are applied to a beam of the cross-section shown with a...

Question 3: Two vertical forces are applied to a beam of the cross-section shown with a uniform thickness of 10 mm. Determine the maximum tensile and compressive stresses at point G located 0.5 m from point A of the beam. Follow the steps below. 60 kN 60 KN Beam Cross-Section 120 mm A Bc 200 mm 1.5m - 1m 1m Step 1-FBD, SFD and BMD diagrams for the beam. Step 2 - Magnitude of moment at point G (located at...
Problem 5 The cross-section shown below is subject to a positive internal bending moment M =...

Problem 5 The cross-section shown below is subject to a positive internal bending moment M = 60 kNm applied about the local z-axis of the section. Determine the maximum tensile and compressive normal stresses in this section due to this internal moment. 200 mm - 25 mm 25 mm 150 mm comp = -79.8 MPa O ten = 118.3 MPa 25 mm 100 mm

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Ten...

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Tensile and Compressive Stresses due to bending, state where on the beam these occur. For the mid-point between A and B, determine shear stress at neutral axis; 2" from the top of the flange; at the junction between web and flange and on the top of the flange for the cross-section. Plot of the bending stress and shear stress distribution diagram across the cross section of...
(7) A moment of M = 4 kip-ft is applied on the cross section shown. Determine...

(7) A moment of M = 4 kip-ft is applied on the cross section shown. Determine (a) the normal stress at point a, (b) the maximum tensile and compressive bending stresses in the beam. Ans: (a) oa = 0.0523 ksi (b) om =-1.779 ksi, om' = 3.72 ksi 10.5 in.al -3 in. +0.5 in. 0.5 in. B 3 in. M 10 in. D +0.5 in.
Please show all steps and applicable diagrams a = 2.0m b = 4.0m c = 2.0m...

Please show all steps and applicable diagrams a = 2.0m b = 4.0m c = 2.0m d = 6.0m e = 3.0m M = 48kN*m w1 = 8kN/m w2 = 6kN/m W1 W2 M BE 5 •d ye Beam DBE has the cross-section shown in the figure to the right Calculate: c) the vertical position y, of the centroid of the girder cross-section, and d) the moment of inertia Ix' about the horizontal axis x'x' passing through the centroid of...

5. H I steel barstock is loaded in tension and Cross section in bending. Draw Mohr's circle at po...

axial stress equals 0 5. H I steel barstock is loaded in tension and Cross section in bending. Draw Mohr's circle at points 1 and 2 at the midspan of the beam, following these steps: 120 lb 2 in. [a] Calculate the weight per unit length of the bar. [lb./ft. Draw complete shear and moment diagrams, including the 120 lb. point load and the beam weight, to find V and M at the midspan. 5 ft. 5ft Ib] e] Calculate...
2) A box beam of rectangular cross section shown is subject to a bending moment Mx=2000...

2) A box beam of rectangular cross section shown is subject to a bending moment Mx=2000 lb in. Find the maximum tensile stress and maximum compressive stress and their respective locations. What is the orientation of the neutral axis? 0.064" 12" 0.04" ... . M. 0.072 0.03"
10 mm 10 mm 300 N/m 50 mm 10 mm Problem 2. Consider the beam above with the cross-section shown. ...

please solve 1-5 and show all steps and equations used 10 mm 10 mm 300 N/m 50 mm 10 mm Problem 2. Consider the beam above with the cross-section shown. The number (300N/m) indicates the value of the load distribution at its peak. (5 pts.) Find the reactions (15 pts.) Draw the shear and moment diagrams using the graphical method. Ensure you state values of the diagrams, and type of function for lincar or higher-order segments. You can indicate all...

3) (35 pts) A L-beam has the cross section shown. A moment M acts about the...

3) (35 pts) A L-beam has the cross section shown. A moment M acts about the x-axis which passes through the centroid of the section. Determine the angle the neutral axis makes with respect to axis. Sketch it on the cross section. Given the design flexural stress limit is 100 MPa, determine the maximum allowable moment which can be applied. You only need to evaluate the stresses at points A, B. Helpful hint: Remember to change the sign of your...