A flat 1018 steel sample was tested in a tensile machine. Sample dimensions are width =...
A flat 1018 steel sample was tested in a tensile machine. Sample dimensions are width = 0.425 inch, thickness = 0.175 inch, original gauge length = 3.45 inch. The sample shows yielding when 3300 lb force is applied with a corresponding change in length of 0.06 inch. From the data, the greatest force applied during testing was 4500 lbs and the sample had elongated by total of 0.5 inch. At fracture, the force applied to the sample decreased to 3000 lbs with a change in length of 0.75 inch.
Determine the area of the sample [in2]
Determine the total strain at failure.
Determine the yield strength.
Determine the ultimate tensile strength.
Homework Answers
Add Answer to:
A flat 1018 steel sample was tested in a tensile machine. Sample
dimensions are width =...
A bar of aluminum is tested under tension, the specimen has a rectangular n with dimensions...
A bar of aluminum is tested under tension, the specimen has a rectangular n with dimensions of 4 mm by 20 mm. The initial length of the sample is 60 mm, the load (force) versus elongation (Aに!finalㅢinitial) graph of this specimen is shown below. a) Determine the ultimate tensile strength. b) Young's modulus c) Total strain after failure 100 63 Fracture ー30 2 3 4 5 Elongation, mm .2 0
Please provide me clear handwriting Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d...
Please provide me clear handwriting
Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d = 7.42, lo = 40mm (4 marks) Load, KN Extension, mm Stress, MPa Strain 0 0 10 0.05 17 0.08 25 0.11 30 0.14 34 0.20 37.5 0.40 38.5 0.60 36 0.90 Cross-sectional Area (A) Modulus of Elasticity (E) Tensile Strength (ST) Percent Elongation (%EL) A = T d2 4 E = Sy Ey ST = PU A %EL = Extension at fracture Gauge...
Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d= 7.42, lo = 40mm (4...
Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d= 7.42, lo = 40mm (4 marks) Load, KN Extension, mm Stress, MPa Strain 0 0 0 0 # 10 0.05 0.0002312 0.00125 17 0.08 0.0003931 0.002 4 25 0.11 0.0005781 0.00275 5 0.14 0.0006937 0.00350 30 34 0.20 0.005 37.5 0.40 0.01 0.0007862 8 0.0008672 2 0.0008903 5 0.0008325 3 38.5 0.60 0.015 36 0.90 0.0225 Cross-sectional Area (A) Modulus of Elasticity (E) Tensile Strength (ST) Percent Elongation (%EL)...
1-Determine the % elongation, yield stress and ultimate tensile strength of the material tested above 2-Calculate...
1-Determine the % elongation, yield stress and ultimate tensile
strength of the material tested above
2-Calculate the elastic modulus of the material tested above
3-If a 200mm cylindrical rod of the material tested above, with
radius 20mm, was subjected to a tensile load of 200kN, what would
the length be?
4-An underground wastewater steel pipe with 2mm walls carries an
ammonia solution of 40 g/m3. The pipe is in contact with
groundwater (assume 0 g/m3 ammonia). Determine the
diffusion rate...
I have a question during my Tensile Test of Sturctural Steel. Ive collected all the data, can you calculate the Elastic...
I have a question during my Tensile Test of Sturctural
Steel.
Ive collected all the data, can you calculate the Elastic
Modulus and referring to the stress strain curve of your samples ,
discuss and compare the results, specify the similarities and
differences if there is any and provide possible reasons.
Thanks
Date of Lab Mark (for tutor only) 1. General information of the sample: Web sample or flange sample? web Specimen dimension (Before Testing) Width, mm Gauge length, mm...
i only need help with Q3 CEE 216 Civil Engineering Materials Steel 1. A 32-mm rebar...
i only need help with Q3
CEE 216 Civil Engineering Materials Steel 1. A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data collected are shown in Table 1. Create a spreadsheet to complete the following. Table 1. Load and displacement data for a 32-mm rebar sample subjected to an increasing tensile load a. Create a plot of stress-strain. Label the axes and show...
A bar of aluminum is tested under tension, the specimen has a rectangular n with dimensions of 4 mm by 20 mm. The initial length of the sample is 60 mm, the load (force) versus elongation (Aに!finalㅢinitial) graph of this specimen is shown below. a) Determine the ultimate tensile strength. b) Young's modulus c) Total strain after failure 100 63 Fracture ー30 2 3 4 5 Elongation, mm .2 0
Please provide me clear handwriting
Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d = 7.42, lo = 40mm (4 marks) Load, KN Extension, mm Stress, MPa Strain 0 0 10 0.05 17 0.08 25 0.11 30 0.14 34 0.20 37.5 0.40 38.5 0.60 36 0.90 Cross-sectional Area (A) Modulus of Elasticity (E) Tensile Strength (ST) Percent Elongation (%EL) A = T d2 4 E = Sy Ey ST = PU A %EL = Extension at fracture Gauge...
Table 1: TENSILE TEST RESULTS OF A METAL SAMPLE with d= 7.42, lo = 40mm (4 marks) Load, KN Extension, mm Stress, MPa Strain 0 0 0 0 # 10 0.05 0.0002312 0.00125 17 0.08 0.0003931 0.002 4 25 0.11 0.0005781 0.00275 5 0.14 0.0006937 0.00350 30 34 0.20 0.005 37.5 0.40 0.01 0.0007862 8 0.0008672 2 0.0008903 5 0.0008325 3 38.5 0.60 0.015 36 0.90 0.0225 Cross-sectional Area (A) Modulus of Elasticity (E) Tensile Strength (ST) Percent Elongation (%EL)...
1-Determine the % elongation, yield stress and ultimate tensile
strength of the material tested above
2-Calculate the elastic modulus of the material tested above
3-If a 200mm cylindrical rod of the material tested above, with
radius 20mm, was subjected to a tensile load of 200kN, what would
the length be?
4-An underground wastewater steel pipe with 2mm walls carries an
ammonia solution of 40 g/m3. The pipe is in contact with
groundwater (assume 0 g/m3 ammonia). Determine the
diffusion rate...
I have a question during my Tensile Test of Sturctural
Steel.
Ive collected all the data, can you calculate the Elastic
Modulus and referring to the stress strain curve of your samples ,
discuss and compare the results, specify the similarities and
differences if there is any and provide possible reasons.
Thanks
Date of Lab Mark (for tutor only) 1. General information of the sample: Web sample or flange sample? web Specimen dimension (Before Testing) Width, mm Gauge length, mm...
i only need help with Q3
CEE 216 Civil Engineering Materials Steel 1. A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data collected are shown in Table 1. Create a spreadsheet to complete the following. Table 1. Load and displacement data for a 32-mm rebar sample subjected to an increasing tensile load a. Create a plot of stress-strain. Label the axes and show...
Most questions answered within 3 hours.
-
Floating Point Representation
Consider a computer that stores information using 10 bits words.
The first bit...
asked 16 minutes ago -
. The theoretical weight percent of carbon in (CH3)3N is:
A. 20.32% B. 81.95% C. 9.97%...
asked 9 minutes ago -
The rate of a certain reaction is given by the following rate
law:
rate = k[H2][I2]...
asked 4 minutes ago -
A 10,000 uF capacitor is in series with a 1 uH inductor. What is
Zeq of...
asked 8 minutes ago -
Draw the molecular orbital diagram for O2-
(oxygen molecule with a negative charge).
asked 25 minutes ago -
Of all the different weapons discussed in this chapter that make
up CBRNE,
Which group do...
asked 22 minutes ago -
Given the following JavaScript code, what will be displayed on
the web page?
var x =...
asked 33 minutes ago -
The cynics, skeptics, epicureans, & stoics were most
philosophies that dealt with:
a. the physical...
asked 35 minutes ago -
The hydronium ion concentration of an aqueous solution of 0.333
M trimethylamine (a weak base with...
asked 36 minutes ago -
A buffer is prepared by partially titrating 50.00 mL of 0.964 M
benzoic acid using 0,100...
asked 39 minutes ago -
For a Generalized Additive Model, what does a large
edf(empirical distribution function) value mean?
Thank you...
asked 52 minutes ago -
questions for Biology lab
An agarose gel electrophoresis assay performed with high quality
will NOT have...
asked 56 minutes ago