5. Write KVL for L1, L2 and L3. Write KCL for nodes A and B. Identify...
please solve problems 1 and problems 2. PROBLEM 1: Derive state-space equations for the following circuit in the form of L1 where χ = :L2 L3 L1 and (a) y 7 V L3 R1 L1 L3 R3 Vt R2 Vc し2 (c) For Part (a), use the file CircuitStateSpace.slx (define the four matrices in Matlab) to verify your derivation using the following numerical values: R1-1; R3-1 R2-10; L1-1e-3 L3-1e-3 L2-10e-2 ; C1-10e-6 PROBLEM 2: (a) What are eigenvalues of the...
java write a method to to find the negative numbers in L1 and L2 (linked list) and put them in L3 .
4. Three inductors with inductances, L1 = 1 H, L2 = 2 H, and L3 = 3 H, are connected to a 5-V power source. What is the effective inductance when the inductors are connected in (a) series (b) parallel.
From the circuit shown below, (a) use KCL and KVL to solve for the three currents. (b) With the given data below and the two currents flowing clockwise, determine both currents using mesh analysis and the voltages across each resistor. r1= 3 Ohms r2= 7 Ohms r3= 2 Ohms r4= 8 Ohms a M 10 V 30 il 222 i2 722 892 i3 12 V W
8051 microcontroller find A= ? B= R6 = L1: SETB C L2: MOV A, #0EAH L3: RRC A L4: MOV R6, #17 L5: XRL A, R6 L6: XCH A, R6 L7: RL A L8: MOV B, R6 L9: SWAP A L10: ANL A, #0CÉH
LI L1= 520mm L2=500mm L3=730mm Calculate the x and y deformations at point A and B given that E=70*10^-3 and diameter for all members is 30mm L = 500 mm 222 520 mm 133730 mm y Figure Q.1 a) Determine the x and y deflection at point A and B given that the diameter of all members is equal to 30 mm
1) In the circuit below the currents are named A, and lc The current direction is determined by the source (out of positive terminal) in the middle and right branches and is clockwise in the left branch · IA flows through R2 and R1 Is flows through R4 and Vb cflows through R3, Vc AB R2 R3 R4 R1 Vb a) Draw the circuit and show the 3 currents described above, including arrows showing the current direction. Show the voltage...
Write C code that perform the same as the assembly code. Hint:data is an integer avariable in C. OUT is a name of a function:- //code part is the following.. L1 LDR R0, =0X006 ;The hexadecimal of 0110 is 0x006 L2 LDR R1, =data L3 LDR R2, [data] L4 AND R2, #0X006 L5 CMP R2, #0X006 L6 BLEQ OUT L7 ..................
units for resistance are in the picture Part 1: Theoretical Applications of KVL, KCL, Superposition and Source Transformation Figure 1 F1 GAIN 4 R10 R2 R1 R3 R11 R8 3k R15 Wr 12 W 3k 10k 10k 2 10k V1 R9 R6 R7 12V V2 R4 RS 2k 3k R14 24Vd 3k 2k 4k 10k R13 Mr 1 R12 4k 3mAdc Figure 1 Contains three independent source and a current dependent current source (F1) 1. along with an extensive network...
For the following design L1-2H C1-0.05F R1.4Ω R2-4Ω C2-0.05P L2-2H Va 4cos(10t+90°)V vb-4cos( 10t+90"N R4-4Ω R6:2Ω RS-4Ω Vc-4cos(20t+90jv vds4cos( 10t+60ον (Remember that i) w is given in rad/sec, ii) the above circuits have different Impedances for different frequencies, ii) we replace the shorted voltage power supplies with a short circuit, iV) with atjb the rectangular form and Ad the polar form we have a-Acos(8), b-Asin(θ), A-: va2+1,7 , θ= tan-l (4)if a > 0, θ= 180-tan-IL) if a <0) a)...