please show me the steps and the equations. I been failing this class and will award points to best answer
please show me the steps and the equations. I been failing this class and will award...
Twenty [kw] of heat is to be removed from 375 [k] water flowing at 0.15 [kg/s] into the inner pipe of concentric tube heat exchanger. Cooling water enters the annulus at 290 [k] and leaves at 320 [k] with a flow in the opposite direction of the inner flow. The diameter of the thin- walled inner pipe is 2.5 [cm] a) b) c) Calculate the exit temperature of the hot fluid and the mass flow rate of the cold fluid...
Hi, please help me with this problem, please explain me step by step and write with very good calligraphy. Solve the next problems: * Water is heated in a horizontal tube. Water enters at a rate of 6 lbm / s and 60 ° F and is heated to 300 ° F. The water flows through an aluminum tube of 3 in diameter. The pipe is heated by an electric resistance ratio of 405Btu / h per foot of pipe...
A counter-flow heat exchanger is stated to have an overall heat transfer coefficient of 284 W/m2.K when operating at design and clean conditions. Hot fluid enters the tube side at 101°C and exits at 71°C, while cold fluid enters the shell side at 27°C and exits at 42°C. After a period of use, built-up scale in the heat exchanger gives a fouling factor of 0.0004 m2 K/W. The surface area is 93 m². Assume both hot and cold fluids have...
Can you please answer the following question 0. (CLO6 - 4 Marks) A counter-flow double-pipe heat exchanger is to heat water from 20°C to 80°C at mass flow rate of 1.5 kg's. The heating is to be accomplished by hot oil available at 150C at a mass flow rate of 2.5 kg/s. The inner tube is thin-walled and has a diameter of 1.5 cm with the length of 60 m. Fluid property: Fluid Type Mass flow rate, The Specific heat,...
please show me the whole work for question 4) and 5),thank you so much An insulating wall is composed of 10 cm of a material having an thermal conductivity of 5 W/m.K, and an unknown thickness of cork, which has a thermal conductivity of 0.045 W/m.K. How thick must the cork be if the heat losses through the wall are to be less than 10W/m2 when the inside temperature is 20degree C and it's -20degree C outside? Water flows through...
Qi. A flat plate of width 1 m and length 0.2m is maintained at a temperature of 32°C. Ambient fluid at 22"C fBlows across the top of the plate in parallel flow. Determine the average heat transfer coefficient, the convection heat transfer rate from the top of the plate, and the drag force on the plate for the following: (a) The Buid is water flowing at a velocity of 0.5 m/s. o) Water is flowing at a velocity of 2.5...
summatize the following info and break them into differeng key points. write them in yojr own words apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...