The falce of Su KN acts in a longitudinal direction Square steel bar(E 2.00K4 Pa) with...
Jf the diameter of the aluminum wire is dea2to.005 and the length is within the talerance rapge ofteat te0t 1pm, Cateutate bhe uncertainte in calculating thi electrical resistance? farce of su KN acts in alengitudinal directian square steel bar(E-2.00K404 Pa) with awidth f 3cn and aheisht of Lem Calculate the resistance change af a aauges when a strain gauge witla eaatge resis tance af t26 AAd a straiA Fate of 2 is bended n a Jf the diameter of the...
Data As x + tid: 5464389_1&course_id - 86783 1 3a. The bar shown is made from a material for which yold = 22 ksi, E=25x10 psi, and 0.28. The bar has a circular cross section with initial diameter d-2 inand initial length L = 36 in 13 kips 13 kips Under the application of the 13 kip load, determine the following: 1. The strain in the bar's longitudinal direction, i.e., its axial strain, 2. the strain in the transverse direction,...
Element 1 is a steel bar that has a circular cross-section with a radius of 30 mm. Element 2 is an aluminum bar that has a circular cross-section with a radius of 50 mm. Element 3 is a steel bar that has a circular cross- section with a radius of 60 mm. Assume for steel, the moduļus, E, is 2.0E11 Pa, and the density, p, is 7800 kg/m3. Assume for aluminum, E-7.0E10 Pa, and p-2700 kg/m3. The rigid, massless rod...
help 7 A 5mm diameter bar made of steel (E=200 GPa) is under 50 kN axial force which results in deflection equal 0.15mm. calculate the bar length in mm * (2 Points) O 10.02 5.36 7.85 12.38
Part B Calculate the load II Review A square steel bar has a length of 2.2 ft and a 1.5 in by 1.5 in cross section and is subjected to axial compression. Under load, the thickness becomes 1.50032 in . If the modulus of elasticity is E = 2.9x 104 ksi and Poisson's ratio is v = 0.31; what is the magnitude of the load that was applied to the bar? Learning Goal To use Poisson's ratio and Hooke's law...
(3pts): The truss is constructed of A36 steel (E -2 a cross-sectional area of 250 mm2. Answer the following s 300 Clbe wna -250 MES, AI 00 G Pa and O, 250 MPa). All truss members have (a) Determine the normal stress and strain in member CD. (b) The support at joint D uses a pin placed in double shear. The pin diameter is 20 mm Determine the average shear stress acting in the pin. 50 kN 50 kN 25...
5 pts Question 10 APL 1/2 * 2 steel bar with nu = -0.33 and E = 29000 ksi is axially loaded is compression with a load of P=40 k. The lateral strain in the bar due to the Poisson's effect is: 4.55 x 10-4 0 -4.55 x 10-4 0 -4.978 x 10-4 O 4978 x 10-4 nunction 11 20 pts
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
A circular cross section steel bar with a Young’s modulus E=2.1x10^11 N/m^2 and an area A=50mm^2 and a length L=3m is installed horizontally between and welded to two walls. Assuming that a torque of M=5,000Nm is applied to the bar at a distance of l=2m from the left wall please answer the following: a. Is this system statically determinate or indeterminate? b. Determine: i. What are the reactions from the walls? ii. Plot the variation of torque in the bar....
2. A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension with a load of 89,000 N and experiences an elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of steel. Give your answer in GPa. 3. A zinc single crystal is being pulled in tension with the normal to its basal plane (0001) at 60° to the tensile axis and the slip...