help 7 A 5mm diameter bar made of steel (E=200 GPa) is under 50 kN axial...

Question

Question

help

Answer 1

Answer #1

Solution - 5 mm Diameter of bar = E-200 G Pa Axial Force P=50kn Deflection 8 0,15 mm Deflection due to ascial force is 8= Pl

Answer 2

Similar Homework Help Questions

5) A bar made of steel (E = 200 GPa, Poisson ratio = 0.32) has the...

5) A bar made of steel (E = 200 GPa, Poisson ratio = 0.32) has the dimensions shown in Fig. 5. If an axial force of P= 80 kN is applied to the bar, determine the change in its length and the change in the dimensions of its cross-section. The material behaves elastically Selastically NOKN 100 mm Fig. 5
Q2 The truss below is made of circular steel bar with diameter 5 cm. Find the axial force for eac...

Q2 The truss below is made of circular steel bar with diameter 5 cm. Find the axial force for each member given that the steel has E-200 Gpa. Use the application posted on the Moodle F 30 kN E 3 m 3 m 60 kN 60 kN 20 kN Figure P-438 Q2 The truss below is made of circular steel bar with diameter 5 cm. Find the axial force for each member given that the steel has E-200 Gpa. Use...
Under an applied axial load of 3,806 kN, the diameter of a bar decreases by 0.23...

Under an applied axial load of 3,806 kN, the diameter of a bar decreases by 0.23 mm from an original diameter of 149 mm. Poisson's ratio for the bar is v= 0.37. Determine the elastic modulus of the bar. Give your answer in GPa.

Problem7: Links BC and DE are both made of steel (E = 200 GPa) and are...

Problem7: Links BC and DE are both made of steel (E = 200 GPa) and are 12 mm wide and 6 mm thick. Determine (a) the force in each link when a 2.4-kN force P is applied to the rigid member AF shown, b) the corresponding deflection of point A 100 mm 50 mm 50 mm 100 mm | 125 mm
A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate...

A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate (see figures. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has diameter 30 mm, the brass tube has outer diameter 45 mm, and the copper tube has outer diameter 60 mm. The corresponding moduli of elasticity are = 210 GPa = 100 GPa, and E= 120 GPa. Calculate the compressive stresses and in the steel,...
The concrete [E = 29 GPa] pier shown in the figure is reinforced by four steel...

The concrete [E = 29 GPa] pier shown in the figure is reinforced by four steel [E = 200 GPa] reinforcing rods, each having a diameter of 19 mm. Assume P = 680 kN, L = 2.10 m, and a = 275 mm. If the pier is subjected to an axial load of 680 kN, determine (a) the normal stress (positive if tensile and negative if compressive) in the concrete and in the steel reinforcing rods. (b) the deflection of...

P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used...

P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 124 MPa and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD 1.8 m 1.8 m 1.35 m
Looking for Help on 10.19. r of solid circular cross section is 50 mm in diameter....

Looking for Help on 10.19. r of solid circular cross section is 50 mm in diameter. The bar is pinned at each end and subject to axial compression. If the proportional limit of the material is 210 MPa and E 200 GPa, determine the minimum length for which Euler's formula is valid. Also, determine the value of the Euler buckling load if the column has this minimum length. Ans. 1.21 m, 412 kN 10.20. The column shown in Fig. 10-10...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...

1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...

A2 m long column made of structural steel with elastic modulus of 200 GPa is loaded...

A2 m long column made of structural steel with elastic modulus of 200 GPa is loaded in axial compression. If the cross section of the column is a 20 mm by 50 mm rectangle, and one end is fixed and the other end is pinned, the maximum axial load that the column can bear before buckling, in kN, is (round to the nearest whole number)