Q2 The truss below is made of circular steel bar with diameter 5 cm. Find the axial force for eac...

Question

Question

Answer 1

Answer #1

3m RV Hence on Rv uadli P H GH +了。 98.28 (temil) F.

Answer 2

Similar Homework Help Questions

help 7 A 5mm diameter bar made of steel (E=200 GPa) is under 50 kN axial...

help 7 A 5mm diameter bar made of steel (E=200 GPa) is under 50 kN axial force which results in deflection equal 0.15mm. calculate the bar length in mm * (2 Points) O 10.02 5.36 7.85 12.38
A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate...

A bar is uniformly compressed by an axial force P 40 kN applied throurhard end plate (see figures. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has diameter 30 mm, the brass tube has outer diameter 45 mm, and the copper tube has outer diameter 60 mm. The corresponding moduli of elasticity are = 210 GPa = 100 GPa, and E= 120 GPa. Calculate the compressive stresses and in the steel,...
The below truss is made from three bars of the same steel material, all of which...

The below truss is made from three bars of the same steel material, all of which have circular cross sections with different diameters. The Young modulus of steel is E= 200 GPa, and yield stress of steel is Gyöeld=200 MPa (in both tension and compression). The force P=7 kN is applied at point C as shown (see Figure 4). All bars are pin connected at their ends. (a) Determine the minimum diameter of the bars so that buckling will not...

Question 5 The members of the truss shown are made of steel and have the cross-sectional areas shown. Use the work e...

Question 5 The members of the truss shown are made of steel and have the cross-sectional areas shown. Use the work energy method to determine the vertical deflection of joint C caused by the application of the 210 kN load. E = 200 GPa 15 m 1200 L5 m 210 kN 1800 Question 5 The members of the truss shown are made of steel and have the cross-sectional areas shown. Use the work energy method to determine the vertical deflection...
1. The members of truss are attached together by pins having 5 cm in diameter and...

1. The members of truss are attached together by pins having 5 cm in diameter and 10 cm in length. The truss is supported by a frictionless pin at one end (joint A) and a roller system at the other joint k). The load Lis equal to 5 kN. The section view of the truss member is below and it is homogeneous all along the truss. Elastic modulus is 200 GPa, shear modulus is 75 GPa for the truss. (a)...
5) A bar made of steel (E = 200 GPa, Poisson ratio = 0.32) has the...

5) A bar made of steel (E = 200 GPa, Poisson ratio = 0.32) has the dimensions shown in Fig. 5. If an axial force of P= 80 kN is applied to the bar, determine the change in its length and the change in the dimensions of its cross-section. The material behaves elastically Selastically NOKN 100 mm Fig. 5

Use MATLAB to determine the five unknown displacements of the following truss and determine the axial...

Use MATLAB to determine the five unknown displacements of the following truss and determine the axial force in all members of the truss. Take A = 0.0015 m^2 and E = 200 GPa for each member. Please post the MATLAB code, as well as the final answers. 2 4 1 3 m 4 13 4 m 7 kN
Steel tube Problem 1.6-3 A polyethylene bar having diameter d = 70 mm is placed inside...

Steel tube Problem 1.6-3 A polyethylene bar having diameter d = 70 mm is placed inside a steel tube having inner diameter d2 = 70.2 mm (see figure). The polyethylene bar is then compressed by an axial force P. At what value of the force P will the space between the polyethylene bar and the steel tube be closed? (For polyethylene, assume E = 1.4 GPa and v = 0.4.) di dz Polyethylene bar
Q2 E (0, 0.8, 0) m (50 point) 2- Figure Q2 depicts the space truss that...

Q2 E (0, 0.8, 0) m (50 point) 2- Figure Q2 depicts the space truss that is belonging to an aircrafts undercarriage system. It has ball and socket supports at C, D, and E. If the force exerted at A by the wheel is F = 10i + 50j + 10k (kN), determine the x-displacement of Joint B. Each bar has the same diameter of 6 cm. The material that used in this frame is aluminum and it exhibits elastic-perfectly...

Bar A bar of a circular cross section of a diameter d = 8.2 mm has...

Bar A bar of a circular cross section of a diameter d = 8.2 mm has a length of L = 5.4 m is fixed at one end and free at the other. A force P = 7.9 kN is applied at the free end of this bar. Determine the stiffness of the bar. Assume E = 200 GPa Give your answer in units of N/mm Select one Oa. 1165.93 Ob 1955.93 c. 62.44 Od. 15451.85