Homework Answers
Add Answer to:
5.a. The box wrench in the Figure below is used to tighten the boltat. If the...
3) A wrench is used to tighten a lug nut on a car, if the force...
3) A wrench is used to tighten a lug nut on a car, if the force is applied to the wrench at a distance 7 from the center of the nut, the radius and force vectors are given below. Calculate the magnitude of the torque vector i acting on the wrench. If the force and radius vectors are in the plane of the page, what direction is the torque into the page or out of the page)? = 'xi o...
The preloads of the M10 bolts used in a pressure vessel are applied with the wrench...
The preloads of the M10 bolts used in a pressure vessel are applied with the wrench shown. For the 16,500 N preload force, Fi, the required torque, T, is approximated as T=K*Fi*d where K-0.20 and d is the nominal bolt diameter. The required torque is developed by applying a force to the end of the wrench as shown. The wrench material is AISI 1035 steel, forged and heat treated. For the applied force, determine the critical failure spot for yielding...
follow australian codes (a) The rigid bolted connection shown in Figure 4 is used to transmit a total vertical load...
follow australian codes
(a) The rigid bolted connection shown in Figure 4 is used to transmit a total vertical load of 350 kN applied as shown. Two bracket plates are connected to the flanges of the I section using the bolt groups (refer figure 4) and hence, the bolts are loaded in- plane. Determine if the bolted connection shown in Figure 4 can safely support the applied load (use cl. 9.4.1 AS4100 1998). The bolts are M20 of 8.8S grade...
Chapter 4, Reserve Problem 018 Three bolts are used in the connection shown in the figure....
Chapter 4, Reserve Problem 018 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 20 mm. The ultimate shear strength of the bolts is 385 MPa, and the ultimate bearing strength of plate (1) is 385 MPa. Determine the minimum bolt diameter required to support an applied load of P = 180 KN if a minimum factor of safety of 2.5 is required with respect to both bolt shear and plate bearing...
please show clear working and box and label each answer! thank you The figure illustrates the...
please show clear working and box and label each answer! thank
you
The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure Pg For the specifications given in the table for the specific problem assigned, select a suitable bolt length, assuming bolts are available in increments of 5 mm. Then determine...
QUESTION 1 A wrench is used to loosen a nut as shown below by applying a...
QUESTION 1 A wrench is used to loosen a nut as shown below by applying a force 13 N. Determine the torque (magnitude and direction:+for CCW and for CW) about the nut joint Express your answer in Sl units with 3 or more significant figures 0.28 m QUESTION 2 The drawing shows a person mass 59 kg. doing push-ups. Find the force exerted by the floor on each foot assuming that the person holds this position Express your answer in...
Please show all working clearly and box and label each answer. thank you The figure illustrates...
Please show all working clearly and box and label each answer.
thank you
The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure Pg For the specifications given in the table for the specific problem assigned, select a suitable bolt length, assuming bolts are available in increments of 5 mm. Then...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in ty...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in typical 0.50 plate 12 000 lb P (b). Two steel plates are joined using 3/8-inch parallel-loaded fillet welds. The yield strength, Sy, and the length of the welds are known. The design factor is 3.5. Determine the maximum tensile...
The figure shows the schematic of a vehicular jack which is to be designed to support a load, W. ...
The figure shows the schematic of a vehicular jack which is to be designed to support a load, W. The links are to be made of A36 structural square tubing, w -40 x 40 x 5 mm. Each link is 300 mm between the centers of the pins, /. Assume each member is centrically loaded Ignore pin holes and stress concentrations. Use nd- 2 a) When 0-70°, determine the greatest allowable load W that can be applied to the jack...
39. What happens to a spaceship flying through space with no engines and no external forces...
39. What happens to a spaceship flying through space with no engines and no external forces acting on the spaceship? A. It gradually slows down. B. It gradually speeds up. C. Its speed doesn't change. D. We have no idea what happens to the spaceship. 40. A 10-N horizontal force is applied to a box that weighs 24 N. If the box does not move on the horizontal surface (m.- 0.5), what is the force of friction? A. 5 N...
3) A wrench is used to tighten a lug nut on a car, if the force is applied to the wrench at a distance 7 from the center of the nut, the radius and force vectors are given below. Calculate the magnitude of the torque vector i acting on the wrench. If the force and radius vectors are in the plane of the page, what direction is the torque into the page or out of the page)? = 'xi o...
The preloads of the M10 bolts used in a pressure vessel are applied with the wrench shown. For the 16,500 N preload force, Fi, the required torque, T, is approximated as T=K*Fi*d where K-0.20 and d is the nominal bolt diameter. The required torque is developed by applying a force to the end of the wrench as shown. The wrench material is AISI 1035 steel, forged and heat treated. For the applied force, determine the critical failure spot for yielding...
follow australian codes
(a) The rigid bolted connection shown in Figure 4 is used to transmit a total vertical load of 350 kN applied as shown. Two bracket plates are connected to the flanges of the I section using the bolt groups (refer figure 4) and hence, the bolts are loaded in- plane. Determine if the bolted connection shown in Figure 4 can safely support the applied load (use cl. 9.4.1 AS4100 1998). The bolts are M20 of 8.8S grade...
Chapter 4, Reserve Problem 018 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 20 mm. The ultimate shear strength of the bolts is 385 MPa, and the ultimate bearing strength of plate (1) is 385 MPa. Determine the minimum bolt diameter required to support an applied load of P = 180 KN if a minimum factor of safety of 2.5 is required with respect to both bolt shear and plate bearing...
please show clear working and box and label each answer! thank
you
The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure Pg For the specifications given in the table for the specific problem assigned, select a suitable bolt length, assuming bolts are available in increments of 5 mm. Then determine...
QUESTION 1 A wrench is used to loosen a nut as shown below by applying a force 13 N. Determine the torque (magnitude and direction:+for CCW and for CW) about the nut joint Express your answer in Sl units with 3 or more significant figures 0.28 m QUESTION 2 The drawing shows a person mass 59 kg. doing push-ups. Find the force exerted by the floor on each foot assuming that the person holds this position Express your answer in...
Please show all working clearly and box and label each answer.
thank you
The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure Pg For the specifications given in the table for the specific problem assigned, select a suitable bolt length, assuming bolts are available in increments of 5 mm. Then...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in typical 0.50 plate 12 000 lb P (b). Two steel plates are joined using 3/8-inch parallel-loaded fillet welds. The yield strength, Sy, and the length of the welds are known. The design factor is 3.5. Determine the maximum tensile...
The figure shows the schematic of a vehicular jack which is to be designed to support a load, W. The links are to be made of A36 structural square tubing, w -40 x 40 x 5 mm. Each link is 300 mm between the centers of the pins, /. Assume each member is centrically loaded Ignore pin holes and stress concentrations. Use nd- 2 a) When 0-70°, determine the greatest allowable load W that can be applied to the jack...
39. What happens to a spaceship flying through space with no engines and no external forces acting on the spaceship? A. It gradually slows down. B. It gradually speeds up. C. Its speed doesn't change. D. We have no idea what happens to the spaceship. 40. A 10-N horizontal force is applied to a box that weighs 24 N. If the box does not move on the horizontal surface (m.- 0.5), what is the force of friction? A. 5 N...
Most questions answered within 3 hours.
-
How can we identify what the horizontal force is when looking at
a merry go round?...
asked 11 minutes ago -
While Dime Community Bank is based in Brooklyn; management has
decided to focus its lending activity...
asked 36 minutes ago -
1) Earnings functions, whereby the log of earnings is regressed
on years of education, years of...
asked 9 minutes ago -
Bruno Corporation is involved in the business of injection
molding of plastics. It is considering the...
asked 15 minutes ago -
What would be the vapor pressure of water at 96°C above a
solution made by dissolving...
asked 30 minutes ago -
Hydration of norbornene
Write the reaction. Discuss the intermediate. Explain how the
equilibrium in the reaction...
asked 37 minutes ago -
Suppose that a party wanted to enter an FRA that expires in 42
days and is...
asked 38 minutes ago -
ABC Ltd. estimated that a new store requires an initial
investment of $800,000. This new store...
asked 38 minutes ago -
1. Review the Nike’s marketing strategy. You must include the
company’s target market, possible market segmentation,...
asked 51 minutes ago -
One of the major advantages of ______________ is to enhance
security for private networks by keeping...
asked 57 minutes ago -
Book:
Title: Framework for
Marketing Management, 15th edition
Author/s: Philip T.
Kotler, Kevin Lane Keller
1....
asked 1 hour ago -
Given Uber’s recent corporate turbulence and ongoing
initiatives, provide a holistic situational analysis of the
environment...
asked 1 hour ago