3) A Woenten a lugnt on a car, if the force is applied to We of the torque vector tacting on the 2) A rope is attached to a wall in three-dimensional space, the other end of the rope is attached to a metal pole that is supported by the rope. The tension force in the rope (E) and the position vector () that is directed along the metal pole are given below. What is the magnitude of the force...
7) Calculate vector ĉ if vector ĉ is equal to the Cross Product of vector ä crossed with vector b, ¿ = axb ā= (4 m) + (-7 m) b = (10 N)X + (-3 N)9 8) A wrench is used to tighten a lug nut on a car, if the force F is applied to the wrench at a distance † from the center of the nut, the radius and force vectors are given as =(0.6 m)2+(-0.419 =(-12 N)X...
After changing a tire on your car, you need to tighten one of the lug nuts to the proper specified torque of 24.0 Nm. How much force is needed if you're pushing down on the end of the 34.0 cm long torque wrench at an angle of 120° with respect to the wrench shaft? O 81.5 N 70.6 N 0 141 N O 7.07 N Question 3 A baseball, with radius 3.20 cm and mass 0.260 kg, is rolling along...
Madison uses a 35.0 cm long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30.0o above the horizontal as shown in the figure, and Madison pulls straight down on the end with a force F = 210 N. How much torque (N m) does Madison exert on the nut? Enter just the numerical value of the answer in Newton-meters, without entering the units. Enter your answer to three significant figures, and remember to include the...
HW05 roblem 4.53 The lug nut on the wheel of the automobile is to be removed using the wrench. The cheater pipe AB is slipped over the handle of the wrench and a force of F-31 N can bo applied at any point and in any direction on the assembly. (Figure 1) Previous Answers Correct Part C gure 1 of 1 Dotermine the greatest possible magnitude of the moment of the force about the z axis Express your answer to...
it to page D Page view A' Read aloud 2 3.The wheel on a car is held in place by four nuts. Each nut should be tightened to 94.0 Nm of torque to be secure. If you have a wrench with a handle that is 0.250 m long, what minimum force do you need to exert perpendicular to the end of the wrench to tighten a nut correctly? 4. The pulley shown in the illustration has a radius of 2.70...
Review Part A The tune-up specifications of a car call for the spark plugs to be tightened to a torque of 41.0 Nm. You plan to tighten the plugs by pulling on the end of a 27.0-cm-long wrench. Because of the cramped space under the hood, you'll need to pull at an angle of 105 with respect to the wrench shaft. With what force must you pull? Submit Request Answer Provide Feedback Review Part A The tune-up specifications of a...
QUESTION 1 A wrench is used to loosen a nut as shown below by applying a force 13 N. Determine the torque (magnitude and direction:+for CCW and for CW) about the nut joint Express your answer in Sl units with 3 or more significant figures 0.28 m QUESTION 2 The drawing shows a person mass 59 kg. doing push-ups. Find the force exerted by the floor on each foot assuming that the person holds this position Express your answer in...
Mail A A wrench 40 cm long lies along the positive y-axls and grips a bolt at the origin. A force is applied in the direction (0, 4,-3) at the end of the wrench. Find the magnitude of the force needed to supply 90 N·m of torque to the bolt Stop 1 The magnitude of the torque τ developed by applying a force F at a point with position vector r at an angle θ to r is given by...
A wrench is used to apply a torque on a bolt as in the picture below. ALL 6 forces that act on the bolt are equal in magnitude. All 6 forces are applied at the same time. If d=0.3 [m] and F1=F2=F3=F4=F5=F6=50[N], what is the torque around the center of the hexagonal bolt? You may use the diagram below. 30° F2 Fi F3 60 F F4 F5 45° Rigid Body Diagram: Force/Torque Table: Forces ma X у TA Net