Hi. please take your time to answer all parts of this question in great detail, please...
A shunt de motor is rated at 6kW, 120V and 1200 r/min has a magnetization curve as shown in Figure 1. The armature resistance is 0.189 and the field resistance is 2002 with and adjustable field resistance of 0 to 4002. The shunt de motor has rated line current of 50A when supplying rated voltage. (a) Determine the value of the adjustable field resistance so that the motor operates at no- load speed of 1200 r/min. [5 marks] (b) Assuming...
a) The input current to a 220 V, short-shunt compound motor at no load is 6 A. The shunt- field circuit resistance is 220 Ω; the armature resistance is 0.112, and the series-field resistance is 0.1 Ω, what is the stray power loss ? (b) Assume the input rating of the motor in Part (a) to be 66 A at 220 V with a no-load speed of 1000 rpm. If the stray power loss varies as the counter-electromotive force and...
QUESTION 1 A) (10 marks) A 10 kW, 250 V DC self-excited shunt generator, with an armature resistance of 0.1 ohm, is delivering 80 % of rated power to the mains at rated voltage when being run at 1000 r.p.m. (revolutions per minute). The field circuit resistance is 220 ohms. The brush contact drop is 0.5 V and rotational (mechanical) losses are 750 W Calculate The induced voltage The electromagnetic torque developed The shaft torque The overall efficiency B) (15...
Question (3) Speed Control [10 Marks A 50 hp, 220 V, 1500 rpm DC shunt motor with an armature resistance of 0.04 Q and a field resistance of 50 Q. The motor has compensating windings, so armature reactance can be ignored. Mechanical and core losses may be ignored also. The moter is driving a load toque that is proportional with speed, Ti a (n). The motor is driving a load with a line current of 80 A and an initial...
Show all working 1. A 4 pole, 220 V, 10 H.P, d.c. shunt motor is rotating at a speed of 320 rpm. Then the developed useful torque is 2. A 4 pole, lap wound d.c. motor drawing an armature current of 20 A has 360 conductors. If the flux per pole is 0.015 Wb then the gross torque developed by the armature of motor is 3. A 220 V, d.c. motor draws an armature current of 20 A. Its armature...
Assignment 02 SET YOUR CALCULATOR TO FIX 3 DIRECT CURRENT MACHINES 0 QUESTION1 An 800-rpm, 440 V, 120 A (armature current), shunt motor has an armature resistance of 0,2 ? The delivered torque is reduced to 60% of the full load value and 15-? resistor is inserted in the armature circuit. Determine the new speed if the supply remains unchanged. QUESTION 2 An 800 rpm, 500 V. 120 A (armature current), series motor has a field resistance of 0.04 ?...
Please, consider this as a single question, and answer it if possible. Any help will be rated for sure. The DC machine, which has the armature resistance Ra=0.12, shunt field winding resistance Rfw=8022 and control rheostat (Rfc), is connected to a 100V DC power supply and operated at a DC shunt motor. At no-load condition, the motor runs at 1000rpm and armature takes 6A. The magnetization curve of the machine at 1000rpm is shown in the Fig. 1. 120 ,...
1. A shunt machine, while running as a generator, has an induced voltage of 260 V at 1200 rpm. Its armature and field resistances are 0.2 2 and 110 Q, respectively. If the machine is run as a shunt motor, it takes 4 A at 220 V (i) Draw the schematic diagram of the machine as a generator. (ii) Draw the schematic diagram of the machine as a motor (iii)At a certain load the motor takes 30 A at 220...
Hi, I need the full worked solution for ALL PARTS of this question please. Final answers to the first 3 parts are given on the right. Neat handwriting is greatly appreciated. Thank you! :) Question 3 (a) Answers: Recall the DC load analysis of an E-MOSFET circuit and determine the following parameters for the circuit given in Figure Q3(a). Assume this particular MOSFET has minimum values of ID(on) = 200 mA at Vos = 4V and VGS(th) = 2V. Vpp=24V...
Choose the correct answer for each question and explain why its right. 1. If it is necessary to reverse the direction of a DC motor, the simplest way to do it is to a. reverse the armature leads b. reverse the polarity of the power supply leads c. add a capacitor between the positive and negative DC voltage leads d. get a reversed wired DC motor In a shunt configured DC motor, the series field is a. attached in series...