The concept use to this problem is induced EMF in the loop.
Initially, from the expression of the EMF calculate the value of the EMF. Later, apply the Ohm’s law to determine the current in the loop. Finally, determine the direction of the current in the loop.
The expression for the EMF is as follows:
Here, B is the magnetic field, l is the length, and v is the velocity vector.
The expression for the Ohm’s law is as follows:
Here, is the potential difference, I is the current, and R is the resistance.
The expression of the induced emf in the loop is as follows:
Substitute for B, for l, and for in the equation .
Rearrange the equation of Ohm’s law for I.
Substitute 0.54 V for and for R in the equation .
As the loop moves more into the field, the flux is increasing. Therefore, the induced field opposes the applied field and the applied field points out. Thus, the induced field points inside. Hence, the direction of current in the loop is Clockwise.
Ans:The magnitude of the current in the loop is equal to 5.40 A and the direction of the current is in the clockwise direction.
The loop in the figure below is being pushed into the 0.20 T magnetic field at...
The loop in the figure is being pulled with a speed 80 m/s into a uniform magnetic field of magnitude B = 0.90 T that is directed into the page. The resistance of the loop is 0.10 Ω and its length is l = 4.00 cm. (Figure 1) What is the direction of the induced current in the loop? Part What is the induced current after the entire loop has entered the uniform magnetic field?
In the figure below is shown a conducting loop being pulled out of a magnetic field at constant speed. The width of the loop is W = 0.27 m, the speed of the loop is v = 9.12 m/s, and magnetic field is B = 0.3 T. Measurement shows that the power being dissipated in the loop is P = 2.558 W as it is being pulled out of the field. What is the resistance of the loop? Give your...
the figure shows a conducting loop in a magnetic field. the radius of the loop is 20 cm, and it has a resistance of 0.02 ohms. Find the magnitude and direction of the induced current if the magnetic field is increasing at a rate of 4 T/s.
A loop is moving through the magnetic field, of strength 1.30 T, at a speed of 53.0 m/s. If the resistance in the loop is 0.200 Ω and the width of the wire is x = 2.00 cm, what is the magnitude of the induced current?
The magnetic field through a 16 cm diameter loop increases from 1.10 T into the page to 2.10 T out of the page in 0.15 s. The resistance of the loop is 0.10 ohms. Find the magnitude and direction of the current in the loop
A flexible circular loop 0.10 m in diameter lies in a magnetic field of 1.80 T, directed into the plane of the diagram. The loop is pulled at the points indicated by the arrows, forming a loop of zero area in 0.20 s. Find the induced emf in the circuit. What is the direction of the current through R (up or down)? 16b. A rectangular conducting loop 0.25 m on a side lies in a magnetic field directed into the...
A rectangular loop of wire is pushed into a region of uniform magnetic field. Given the data in the figure, what is the magnitude of the emf induced in the one-turn loop? B into page B=0.60 T 0.20 m 10 ms ® 0.50 m 3.00 V 0.120 V 1.20 V 0.300 V 6.00 V
A square loop 10 cm on a side is placed in a uniform, time-varying magnetic field perpendicular to the plane of the loop, as indicated in the figure below. The field has an instantaneous magnitude of 0.63 T and is increasing at the rate of 0.33 T/ms. The loop has a resistance of 0.0162. (a) Find the loop's magnetic moment. magnitude direction Select (b) Find the torque on the loop A square loop 10 cm on a side is placed...
A magnetic field of magnitude B(t) = Boeßt pierces the loop shown in the figure in a direction perpendicular to the plane of the loop. B. = 3.33 T and B = 2.22 s-1. The loop is made of cylindrical copper wire, whose radius is r=0.444 mm. The resistivity of copper is p= 1.68 x 10-812.m. The radius of the loop is 12.2 cm. What is the magnitude of the electric field induced in the loop at time t =...
A magnetic field of magnitude B(t) = Boeßt pierces the loop shown in the figure in a direction perpendicular to the plane of the loop. Bo = 3.33 T and B = 2.22 s-1. The loop is made of cylindrical copper wire, whose radius is r=0.444 mm. The resistivity of copper is p= 1.68 x 10-8 2. m. The radius of the loop is 12.2 cm. What is the magnitude of the electric field induced in the loop at time...