P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside...

Question

Question

P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside a hollow aluminum cylinder of internal diameter 75 mm

Answer 1

Answer #1

P = 1000 KN = 1000×1000N

Answer 2

Similar Homework Help Questions

the hollow tube down has an outside diameter of 45 mm and an inside diameter of...

the hollow tube down has an outside diameter of 45 mm and an inside diameter of 40 mm. the tube is made of an aluminum alloy with a minimum yield strength of 280 MPa. the bending load is F =1.5 kN, the axial load is P = 10kN and the twisting moment is T = 70 N-m. Determine the factor of safety based on the stress at point A using (a) the maximum shear stress theory and (b) the distortion...
Q2. A hollow mild steel column has 25mm thickness and is 20cm in external diameter with...

Q2. A hollow mild steel column has 25mm thickness and is 20cm in external diameter with 6m length. The modulus value for mild steel is 1.2 x 106 N/mm² and this column is hinged at both ends find the Euler's crushing load and compare the load with the crushing load given by the Rankine's formula Determine for what length these two formulae will give the same crushing load? Finally Calculate the critical stresses for the series of strut having slenderness...
A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate...

A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate the allowable torque that can be transmitted if the allowable shear stress is 62 MPa. When the allowable torque is applied, calculate the shear stress at the inner surface of the shaft.

A steel bar , area 625 mm^2 , is embedded in block of concrete 100mm ×...

A steel bar , area 625 mm^2 , is embedded in block of concrete 100mm × 100mm. The length of both the steel bar and concrete block is 300 mm . Assuming a value of 210kN/mm^2 for young modulus for steel and 14 kN/mm^2 for concrete , determine the load carried by the steel and the load carried by the concrete , if the combined section is subject to a compressive load of 5kn . assume that there os no...
1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel...

1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel tube of outer diameter d3 = 37.5 mm and inner diameter d2 = 30.0 mm (see figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar has a length L = 600 mm and is twisted Tube by a torque T = 400 N-m acting on the...
please answer 18.11 and 18.12 18.11 A steel ring with an outside diameter of 150 mm and an inside diameter of 100 mm...

please answer 18.11 and 18.12 18.11 A steel ring with an outside diameter of 150 mm and an inside diameter of 100 mm is shrunk onto another steel ring with an inside diameter of 50 mm. An axial force of 56,54 kN is needed to push the rings apart. Calculate the pressure at the mating surface and the shrinkage allowance given that both rings are 20 mm thick and the coefficient of friction between the mating surfaces is 0,2. Using...

1. A closely coiled helical spring made of 15 mm diameter steel wire has 15 coils...

1. A closely coiled helical spring made of 15 mm diameter steel wire has 15 coils of 110 mm mean diameter. The spring is subjected to an axial load of 180 N. Calculate the maximum shear stress induced in the spring. Assume modulus of rigidity is 78 GPa. 2. A solid circular bar ABC consists of two segments, as shown in the figure. One segment has diameter d1= 65 mm and length L1 = 1.54 m; the other segment has...
A 50-mm-diameter steel tube with a wall thickness of 2 mm just fits in a rigid...

A 50-mm-diameter steel tube with a wall thickness of 2 mm just fits in a rigid hole. Find the tangential stress if an axial compressive load of 10 kN is applied. Assume υ = 0.30 and E = 200 X 10 N/m . Neglect the possibility of buckling.
Engineering materials b) A mild steel rod of 4 cm diameter was tested for tensile strength...

Engineering materials b) A mild steel rod of 4 cm diameter was tested for tensile strength with the gauge length of 60 mm. The following observations were recorded: Final length = 9 cm; Final diameter = 8 mm; Yield load – 5.4 kN and Ultimate load – 8.1 KN. (4 Marks) Calculate 1. Yield stress (1 Mark) 2. Ultimate tensile stress (Mark) 3. Percentage reduction in area. (1 Mark) 4. Percentage elongation (IMark)

3. Show that the length of a bar subjected to an axial load P is AL...

3. Show that the length of a bar subjected to an axial load P is AL = PL/AE. 4. A hollow copper cylinder (OD = 10 in and ID = 5 in) contains a solid steel core. Determine the compressive stresses in the steel and the copper when a force of 200,000 lb is applied with a press.