ANSWER A:
Isolation transformers are used for isolation of conduction paths between primary and secondary windings to protect it from unnecessary current and DC component of signals. Hence the Answer is C .
ANSWER B:
As turns ratio is 4, which is equal to Primary Voltage / Secondary Voltage. So, the Secondary Voltage is Primary Voltage / Turns Ratio, which is equal to 480/4, that is 120 V. So, Answer is D.
For any queries, leave a comment. And a thumbs up is always appreciated. Thanks.
QUESTION7 What is an isolation transformer? O A transformer which allow current to flow from the...
Q-1 A 60Hz, 480V/240V,960V A transformer is supplying a 960W passive load at 240V. The resistances of the primary side and secondary side of the transformer are 1.092 and 0.252 respectively. If the no load losses of the transfomer is given by P-Vã 4800 W where Vn is the input voltage of the transformer in Volt. Answer the following: a) Calculate transformer efficiency b) Do you allow this transformer to be connected to 240V 50Hz distribution system? Explain. c What...
A transformer steps down voltage from 1000V to 120V. The primary coil carries 2A and has 1000 turn. How many turns does the secondary coil have?
ircuit for which R = 20 14. (a) Calculate the resonant angular frequency of an RLC series circuit for which R= 200 and C = 4.0uF. (b) If R is changed to 300 , what is the resonant angular frequency?! , L = 75 mH , -O- (a) senes (b) time current direction L -C 15. A transformer has a primary coil of 500 turns and a secondary coil of 10 turns. If Vprimary = 120 V rms, and the...
Learning Goal: To understand the concepts explaining the operation of transformers.One of the advantages of alternating current (ac) over direct current (dc) is the ease with which voltage levels can be increased or decreased. Such a need is alwayspresent due to the practical requirements of energy distribution. On the one hand, the voltage supplied to the end users must be reasonably low for safety reasons(depending on the country, that voltage may be 110 volts, 220 volts, or some other value...
Capacitor
is connected to secondary
(1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transformer is connected to a 50Hz, 230Vus power supply. A 2700μF filter capacitor is used. A current of 1.5 Amp is drawn from the supply (i) Sketch a schematic diagram of the setup (ii) Calculate the mean dc output voltage (ii) Assume that each diode conducts for one-twelfth...
Electricity is distributed from electrical substations to neighborhoods at 1.4x104 V. This is a 60Hz oscillating (AC) voltage. Neighborhood transformers, seen on utility poles, step this voltage down to the 120V that is delivered to your house. Part A How many turns does the primary coil on the transformer have if the secondary coil has 150 turns? Express your answer using two significant figures. VA - ? neprim turns Submit Request Answer Part B No energy is lost in an...
comovaleyschoolsinstructure.ccm Viccaria Mosde LME Login 1Ouize: Tea Luodor Search foruts A 240 V motor draws 9.0 A ot current at start up. At normal operating speeds the same motor only drawws 2.5 A. What is the back emt ot this motor at nonmal operating spcods? 57 V O 120V 240v Calenda Question 31 2 pts Inbox The ooil of a motor has a resistance of 4.1 ahms. The mator is plugged into a 120 V outlet, and the coil develops...
PLEASE INDICATE WHICH LETTER YOU USED TO SOLVE AND THE
NUMERICAL ANSWER WITH UNITS!!
Please mark your answers to the multiple choice questions and put the final number with correct units for the questions which require calculations. For each question involving calculations, the multiple choice part weights 5 points: correct number (sign/direction) - 9 points; correct units 1 point. Use scratch paper for your calculations but don't submit it. Submit only this file with your answers. 4. (15 points) The...
2) A portable x-ray unit has a step-up transformer, the 120 V input o which is transformed to the 100 kV output needed by the x-ray tube. The primary has 50 loops and draws a current of 10.00 A when in use. (a) What is the number of loops in the secondary? (b) Find the current output of the secondary 3)Calculate the magnitude of the induced emf when the magnet in Figure (a) is thrust into the coil, given the...
1 A single phase AC system Consider a single phase AC distribution system in which there a single home connected to a 10kVA service transformer. Let’s assume that the primary of the distribution transformer can be modeled as an ideal 240V (rms) AC source and that the effective impedance of the transformer is 2% resistance and 3% reactance. (See lecture notes for converting % to Ohms). Connected to the secondary of the transformer is 200 ft of #6 AWG aluminum...