A 714 W heating unit is designed to operate with an applied potential difference of 117 V. (a) By what percentage will its heat output drop if the applied potential difference drops to 112 V? Assume no change in resistance. (b) If you took the variation of resistance with temperature into account, would the actual drop in heat output be larger or smaller than that calculated in (a)?
A 714 W heating unit is designed to operate with an applied potential difference of 117...
A "2000 WW" electric heater is designed to operate on a 230VV
supply.
A "2000 W" electric heater is designed to operate on a 230V supply Part A What is its operating resistance? Express your answer with the appropriate units. μΑ ? R= Value Units Submit Request Answer Part B What current does it draw? Express your answer with the appropriate units. μΑ ? I = Value Units Submit Request Answer Part C If the voltage drops to 220 V,...
A "2100 W" electric heater is designed to operate on a 230V supply. What is its operating resistance? Express your answer with the appropriate units. ЦА ? R= Value Units Submit Request Answer Part B What current does it draw? Express your answer with the appropriate units. μΑ ? I= Value Units Submit Request Answer Part If the voltage drops to 220 V, what power does the heater take? (Assume that the resistance is constant. Actually, it will change because...
Q1
a) Company A designed a heat pump to
supply heat into a library in Canada during
winter, so that the library can maintain to be at 20°C. The heat
pump utilizes
12,000 L/min of Refrigerant-134a as the working fluid and absorb
heat from an
industrial water stream. The water stream enters the evaporator at
50°C and exits
at 25°C. The refrigerant enters the evaporator at 10°C with 90%
moisture content
and leaves at 20°C. There is no pressure drop in...
EG 171 Test Chapters 7 Date: 214れ ,3& Name 24. The amount by which the actual resistance can differ from the color-coded value is the: a. temperatare coefficient b. power rating e differiential resistance D tolerance 25. The resistance value of a chip resistor is determined from the size of the resistor three digit number printed on the body d. color-code c. three letters printed on the body True/False Indicate whether the statement is true or false 26. The practical...
Chose the correct answer(s) from the multiple choice lists below 1. Exergy of a system is a) b) always increasing e) guided by the first and second laws of thermodynamics for reversible processes only Un d) limited by the second law of thermodynamics for all processes. processes, it is destroyed partly or completely). e) equal to the Gibs free energy of the system. 211two electrodes, one made of u (E.-3.06 V) and another made of Cu ΟΕ.+034V placed in an...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
I only need help with the discussion
there are many info that you do not need put I put just in
case as well as my data table.
please do it as soon as u can
Meauements ODeit1 Check2 Meaurements Checi3 Ced Check5 Check6 Measurements Check7 heck8 4058 33 536 1502 1035 979 119478 041 1.0319|0.554972| 64261| 153|15542033681 995781 5266566 1578807 298h 1631 119 1209430016 079096812 0.418135246 0,00032665 011890:004668155728441 0293237 1.291809502 1.22833 1.28 1952 -1116 4281 140616885511984206317 3346 8162 0.78...
For the preparation and standardization of NaOH with KHP im supposed to boil water for 1hr and 30 min to remove CO2....the problem is that if I don't boil it for that long and (30 min) b/c of not enough time but I put the water I boiled for 1/2 hr aproximately into a NaOH bottle with a CO2 absorber and stored it there for a few days. I would assume that I would have to boil the water again...but...