A company needs to pump coconut oil (den: 924 kg/m^3) from the import truck to its holding tank 24 meters above the ground. What is the lowest pressure pump that can lift it to this height? Give answer in ATM units.
A company needs to pump coconut oil (den: 924 kg/m^3) from the import truck to its...
A company needs to pump coconut oil (den: 924 kg/m^3) from the import truck to its holding tank 20 meters above the ground. If the pump that is used is able to create 2 ATM of pressure, what will be the velocity of the oil as it enters the tank?
(2) The work required to pump the fluid from a tank (between a units and b units above the bottom of a tank) of constant mass-density p out to a height h above the bottom of the tank is given by W- pg(cross-sectional area at y)(distance fluid at y needs to be lifted) dy where g is the acceleration due to gravity and y is the distance from bottom of the tank. Note: Water has a mass-density of p 10...
5 points WORK LIFT PROBLEM An inverted conical tank at a chemical plant has a base radius of 4 m and height of 3 m and is completely filled with liquid nitrogen, which has a density of 808.4 kg/m3. The Earth's gravitational constant is -9.8 m/s2. How much work is needed to pump all of the liquid nitrogen up through an outflow pipe that empties 3 meters above the top of the tank? (Note that the conical tank is opening...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
A U-tube contains liquid of unknown density. An oil of density
770 kg/m³ is poured into one arm of the tube until the oil column
is 13.5 cm high. The oil-air interface is then 4.5 cm above the
liquid level in the other arm of the U-tube. Find the density of
the liquid.
A raft is made of 11 logs lashed together. Each is 38.0 cm in
diameter and has a length of 7.00 m. How many people (whole number)...
please help! this is a fluids question in physics.
1-3 (a) What is the height of a fluid column in a barometer that uses water as its 5 pts fluid in 0.924 atm of air pressure? The density of water is 1000 kg/m'. Neglect the vapor pressure in the apparently empty space above the column. Use g = 9.80 m/s² and give the height in meters. m( + 0.02 m) (b) What is the height if the fluid is mercury?...
Please show all work Neatly
8. A rectangular object has a mass of 0.8 kg and the following dimensions of length, width, and height: 1 = 10.0 cm, w = 3.0 cm and h = 2.0 cm. a) Calculate the density of this object in units of g/cm? Report your answer with the proper number of significant figures. (6 points) d=m:V 1kg = 1000 g b) Calculate the pressure that this object will exert on a surface placed so that...
you can skip task 1 (3) because its a code in
matlab.
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter ofthe pipe is equal to 30 cm water is to be pumped...
Case 27 To Use or Not to Use?
Beaufort Sea Production Company (BSPC) operates a medium-sized oil
field on Alaska’s north coast. The field is still producing at its
maximum rate, 325,000 barrels of oil per day (BOPD). However, to
sustain this rate the company started a waterflood of the reservoir
two years ago. Now a capacity bottleneck in the water disposal
process is threatening to curtail production. In waterflooding,
salt water from the Beaufort Sea is treated to remove...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...