What is the magnitude of the primary line current of a 14,000 – 480Y/277 V, delta-wye,...
What is the magnitude of the primary line current of a 14,000 –
480Y/277 V, delta-wye, three-
phase distribution transformer if a 200kW, 0.88 P.F. lagging load
is connected to the secondary.
(assume that the transformer is lossless and that the primary is
the high-voltage side)
Homework Answers
Add Answer to:
What is the magnitude of the primary line current of a 14,000 –
480Y/277 V, delta-wye,...
Problem 4 Three ideal single-phase transformers are connected in a delta/wye configuration with the primary side of the...
Problem 4 Three ideal single-phase transformers are connected in a delta/wye configuration with the primary side of the three-phase transformer rated at 120 kV and the secondary side rated at 13.8 kV. The rated power of the transformer bank is 20 MVA. One side of the transformer bank is connected to a 120 kV transmission line, and the other side is connected to a three-phase load of 15 MVA at 0.85 lagging power factor. Compute the following: a) The turns...
4-9 Question Completion Status: QUESTION 4 A three phase delta source is connected to a three...
4-9
Question Completion Status: QUESTION 4 A three phase delta source is connected to a three phase transformer. The primary of the transformer is connected in a delta configuration The line voltage on the primary is 240V. The turns ratio is 2:1. The secondary of the transformer is connected in a wye configuration. A wye connected load is attached to the secondary of the transformer. Each of the three load resistors has a resistance of 10 ohms. What is the...
What is the answer for questions 2-5? Questions: 1. Delta-Wye and Wye-Delta configurations both produce: a)...
What is the answer for questions 2-5?
Questions: 1. Delta-Wye and Wye-Delta configurations both produce: a) Increases in secondary voltages and currents. b) Decreases in the secondary voltages and currents. c) Phase shift between the incoming and outgoing line voltages. d) Additional V3 increases in the secondary voltages and currents. ANSWER: Choose an item. 2. The line voltage at the secondary of a 10:1 wye-delta connected transformer will be: a) Equal to the line voltage at the primary times b)...
A delta-wye connected transformer is shown in Figure below. This is a 220 kV to 450...
A delta-wye connected transformer is shown in Figure below. This is a 220 kV to 450 kV transformer, line-line, RMS. The 'X' side is the 220 kV side. Assume that Phase A voltage on the X' side has zero phase angle (that is, use VaX as the phase reference) 1) What is the turns ratio NX: NH? 2) Draw phasor diagrams of the primary and secondary voltages. Be sure to get relative phase angles right. 3) If a balanced load...
A 150 KVA, 2080/208-V, 3 PHASE, delta-wye transformer with the following: RH 450m2 R 4.5m XH 2.20...
A 150 KVA, 2080/208-V, 3 PHASE, delta-wye transformer with the following: RH 450m2 R 4.5m XH 2.20 Load 120 KVA, 90KW (lagging power factor) at rated terminal voltage of 208V Determine a) b) c) The approximate equivalent circuit referred to the low-voltage side The primary voltage The transformer efficiency Please show the following: Circuit with the values given & found Equations used
A 150 KVA, 2080/208-V, 3 PHASE, delta-wye transformer with the following: RH 450m2 R 4.5m XH 2.20 Load...
A three phase 250 kVA 2400:415 V 50 Hz distribution transformer is constructed by connecting thre...
A three phase 250 kVA 2400:415 V 50 Hz distribution transformer is constructed by connecting three single phase transformers in the Dynll vector group as shown in Fig.P1. The per phase equivalent circuit parameters on the high voltage side are: R1-0.72 Ω, Xi,-0.92 Ω, R2-0.70 Ω, Xp-0.90 Ω, R.-308.49 Ω, and X,,-44.61 Ω (a) Sketch the corresponding phasor diagram of the primary and secondary voltages for the Dynll vector group; lagging; terminal voltage is 415 V line to line, and...
1. In order to meet an emergency, three single-phase transformers with 12.470/7.200 V are connected in...
1. In order to meet an emergency, three single-phase transformers with 12.470/7.200 V are connected in Delta-Wye to form a three-phase transformer which is fed by a 12.470 V transmission line. If the transformer supplies 60 MVA to a load, calculate: (3 marks) a. The turns ratio for each transformer b. The currents in the primary and secondary windings of the transformer c. The primary and secondary transmission line currents 2. A Wye-Delta transformer is connected to a 66 kV...
Calculations. The following system has a WYE Primary, Delta Secondary, and a WYE configuration for the...
Calculations. The following system has a WYE Primary, Delta Secondary, and a WYE configuration for the load. The given values for this system are; Primary Line Voltage 4160 VAC Secondary Line Voltage 440 VAC Calculations. The following system has a WYE Primary, Delta Secondary, and a WYE configuration for the load. The given values for this system are; Primary Line Voltage 4160 VAC Secondary Line Voltage 440 VAC
Three single-phase transformers are connected in a wye-delta configuration to step down a line voltage of...
Three single-phase transformers are connected in a wye-delta configuration to step down a line voltage of 13.8kV to 4160V to supply an industrial facility. The plant draws 8MW at a 0.80 power factor. Transformer impedances can be neglected. Calculate the following: a. the apparent power (SL) drawn by the load/plant. b. the apparent power (Ss) furnished by the HV source. c. the current in the HV lines (141) d. the current in the LV lines (112) e. the currents in...
A balanced three-phase network supplies a balanced load through a three-phase wye-wye connected transformer as shown...
A balanced three-phase network supplies a balanced load through a three-phase wye-wye connected transformer as shown in the following figure. Transformer Supply Network B8 Load Y-Y The wye-wye connected transformer has the following parameter: S 25 MVA Xir 15% 240/132 kV The three-phase load parameters are: Pload 20 MW pfload 0.8 The three-phase supply network line voltage and short circuit current are: Vnet 225 kV Inet_short= 15 kA. A. Calculate primary and secondary current rating. B. Calculate trans former actual...
Problem 4 Three ideal single-phase transformers are connected in a delta/wye configuration with the primary side of the three-phase transformer rated at 120 kV and the secondary side rated at 13.8 kV. The rated power of the transformer bank is 20 MVA. One side of the transformer bank is connected to a 120 kV transmission line, and the other side is connected to a three-phase load of 15 MVA at 0.85 lagging power factor. Compute the following: a) The turns...
4-9
Question Completion Status: QUESTION 4 A three phase delta source is connected to a three phase transformer. The primary of the transformer is connected in a delta configuration The line voltage on the primary is 240V. The turns ratio is 2:1. The secondary of the transformer is connected in a wye configuration. A wye connected load is attached to the secondary of the transformer. Each of the three load resistors has a resistance of 10 ohms. What is the...
What is the answer for questions 2-5?
Questions: 1. Delta-Wye and Wye-Delta configurations both produce: a) Increases in secondary voltages and currents. b) Decreases in the secondary voltages and currents. c) Phase shift between the incoming and outgoing line voltages. d) Additional V3 increases in the secondary voltages and currents. ANSWER: Choose an item. 2. The line voltage at the secondary of a 10:1 wye-delta connected transformer will be: a) Equal to the line voltage at the primary times b)...
A delta-wye connected transformer is shown in Figure below. This is a 220 kV to 450 kV transformer, line-line, RMS. The 'X' side is the 220 kV side. Assume that Phase A voltage on the X' side has zero phase angle (that is, use VaX as the phase reference) 1) What is the turns ratio NX: NH? 2) Draw phasor diagrams of the primary and secondary voltages. Be sure to get relative phase angles right. 3) If a balanced load...
A 150 KVA, 2080/208-V, 3 PHASE, delta-wye transformer with the following: RH 450m2 R 4.5m XH 2.20 Load 120 KVA, 90KW (lagging power factor) at rated terminal voltage of 208V Determine a) b) c) The approximate equivalent circuit referred to the low-voltage side The primary voltage The transformer efficiency Please show the following: Circuit with the values given & found Equations used
A 150 KVA, 2080/208-V, 3 PHASE, delta-wye transformer with the following: RH 450m2 R 4.5m XH 2.20 Load...
A three phase 250 kVA 2400:415 V 50 Hz distribution transformer is constructed by connecting three single phase transformers in the Dynll vector group as shown in Fig.P1. The per phase equivalent circuit parameters on the high voltage side are: R1-0.72 Ω, Xi,-0.92 Ω, R2-0.70 Ω, Xp-0.90 Ω, R.-308.49 Ω, and X,,-44.61 Ω (a) Sketch the corresponding phasor diagram of the primary and secondary voltages for the Dynll vector group; lagging; terminal voltage is 415 V line to line, and...
1. In order to meet an emergency, three single-phase transformers with 12.470/7.200 V are connected in Delta-Wye to form a three-phase transformer which is fed by a 12.470 V transmission line. If the transformer supplies 60 MVA to a load, calculate: (3 marks) a. The turns ratio for each transformer b. The currents in the primary and secondary windings of the transformer c. The primary and secondary transmission line currents 2. A Wye-Delta transformer is connected to a 66 kV...
Calculations. The following system has a WYE Primary, Delta Secondary, and a WYE configuration for the load. The given values for this system are; Primary Line Voltage 4160 VAC Secondary Line Voltage 440 VAC Calculations. The following system has a WYE Primary, Delta Secondary, and a WYE configuration for the load. The given values for this system are; Primary Line Voltage 4160 VAC Secondary Line Voltage 440 VAC
Three single-phase transformers are connected in a wye-delta configuration to step down a line voltage of 13.8kV to 4160V to supply an industrial facility. The plant draws 8MW at a 0.80 power factor. Transformer impedances can be neglected. Calculate the following: a. the apparent power (SL) drawn by the load/plant. b. the apparent power (Ss) furnished by the HV source. c. the current in the HV lines (141) d. the current in the LV lines (112) e. the currents in...
A balanced three-phase network supplies a balanced load through a three-phase wye-wye connected transformer as shown in the following figure. Transformer Supply Network B8 Load Y-Y The wye-wye connected transformer has the following parameter: S 25 MVA Xir 15% 240/132 kV The three-phase load parameters are: Pload 20 MW pfload 0.8 The three-phase supply network line voltage and short circuit current are: Vnet 225 kV Inet_short= 15 kA. A. Calculate primary and secondary current rating. B. Calculate trans former actual...
Most questions answered within 3 hours.
-
There is X-linked mutations in flies in this example. You need
to determine the inheritence pattern...
asked 52 seconds from now -
1) There is a 5.0 μC charge at each of 3 corners of a square
(each...
asked 10 minutes ago -
A study of 420,095 cell phone users found that
134 of them developed cancer of the...
asked 13 minutes ago -
2.50 g of NH4Cl is added to 12.9 g of water. Calculate the
molality of the...
asked 16 minutes ago -
Part 1
(a) Calculate the pH at 25°C of a 0.10 M solution of a
weak...
asked 18 minutes ago -
1-Calculate the mass in grams of 2.55 moles of KCl
2- Calculate how many moles are...
asked 46 minutes ago -
Bright Sun, Inc. sold an issue of 30-year $1,000 par value bonds
to the public. The...
asked 40 minutes ago -
Bismuth-210 is beta emitter with a half-life of 5.0 days.
Part A
If a sample contains...
asked 32 minutes ago -
The income statement for the month of June, 2014 of Happy Smiles
Enterprises contains the following...
asked 45 minutes ago -
To be done in java code. 2 words are anagrams if 1 word can be
formed...
asked 43 minutes ago -
Two players take turns at removing 1 to 4 coins from an original
pile of 16...
asked 39 minutes ago -
1. Choose value for p between 0.20 and 0.80. It should have at
least two decimal...
asked 47 minutes ago