A steel rotating shaft is subjected to a nending moment of 150Nm and a force F...
Homework Answers
To solve this problem, i have assumed some data which i think you have forgotten to provide. ie. The shaft has circular cross-section of radius 100mm.
Although i have solved the problem in the more general way so that you will not find any difficulty.
Hope the solution helps you
For any other query, you can drop a comment.
Add Answer to:
A
steel rotating shaft is subjected to a nending moment of 150Nm and
a force F...
A rotating circular shaft, machined from AISI 1095 Q&T steel, is subjected to a torque that...
A rotating circular shaft, machined from AISI 1095 Q&T
steel, is
subjected to a torque that varies from a value of 200 N.m to 400
N.m
and to a fluctuating bending moment that varies from a value of
-100
N.m to 300 N.m. Also an axial tensile force of 5 kN acts on the
element.
The torque and the bending moments have their peak values at
the
same time and their frequencies are same. Find the factor of
safety of...
The rotating shaft shown in the figure is machined and ground from a steel with a yield strength of 373 MPaand an ultimate strength of 430 MPa. It is subjected to a force of F 6.4 kN and operat...
The rotating shaft shown in the figure is machined and ground from a steel with a yield strength of 373 MPaand an ultimate strength of 430 MPa. It is subjected to a force of F 6.4 kN and operates at about 300 C. Find the minimum factor of safety for fatigue based on infinite life if a reliability of99% is desired. All dimensions in the figure are in mm. 25 D r50 D 25 D -35 D I R 20...
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as if...
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as iflustra values 2000N.m and 3000 transmitted torque T-4000 N.m .The shaft is made of hardened steel having (Sy-900 MP, Su-1200 MP. ),and all important surfaces are finished by grinding For reliability of 99% and a safety factor of 2.5. (a) Determine the diameter d against static failure (b) Determine the diameter d against fatigue failure using Goodman approach if D-1.1d...
In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A= 400 lbr
In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A= 400 lbr .and at C = 800 Ibr. These radial forces are caused by spur gears mounted to shaft (a result of the pressure angle of the teeth, 20 degrees) that mesh with 2 other spur gears, not shown. Also, The shaft transmits a constant torque of 11110 in-lbr (925 ft-lbr) due to the tangential force (Wt: transmitted load) at C of...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20". The shaft transmits a torque to point A of TA = 340 N.m. The shaft is machined from steel with Sy= 420 MPa and Sut = 560 MPa. The fatigue...
The rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F=6 kN.
Problem 4: The rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F=6 kN. Find the maximum factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding. All dimensions are in mm.
The rotating shaft in the glven figure is machined from AISI 1020 CD steel. It is subjected to a force of F= 7 kN.
The rotating shaft in the glven figure is machined from AISI 1020 CD steel. It is subjected to a force of F= 7 kN. Find the minimum factor of safety for fatigue based on Infinite life. Be sure to check for yielding. What are the values of the theoretical stress-concentration factor, the notch sensitivity. and the fatigue stress concentration-factor? The value of the theoretical stress-concentration factor is _______ The value of the notch sensitivity is _______ The value of the fatigue stress-concentration factor is...
The rotating solid steel shaft is simply supported by bearings at points B and C and...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diam...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
Please answer A and B. The rotating solid stedl shaft is simply supported by bearings at...
Please answer A and B.
The rotating solid stedl shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20. The shaft transmits a torque to point A of TA-340 N m. The shaft is machined from steel with Sy- 420 MPa and Sut-560...
A rotating circular shaft, machined from AISI 1095 Q&T
steel, is
subjected to a torque that varies from a value of 200 N.m to 400
N.m
and to a fluctuating bending moment that varies from a value of
-100
N.m to 300 N.m. Also an axial tensile force of 5 kN acts on the
element.
The torque and the bending moments have their peak values at
the
same time and their frequencies are same. Find the factor of
safety of...
The rotating shaft shown in the figure is machined and ground from a steel with a yield strength of 373 MPaand an ultimate strength of 430 MPa. It is subjected to a force of F 6.4 kN and operates at about 300 C. Find the minimum factor of safety for fatigue based on infinite life if a reliability of99% is desired. All dimensions in the figure are in mm. 25 D r50 D 25 D -35 D I R 20...
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as iflustra values 2000N.m and 3000 transmitted torque T-4000 N.m .The shaft is made of hardened steel having (Sy-900 MP, Su-1200 MP. ),and all important surfaces are finished by grinding For reliability of 99% and a safety factor of 2.5. (a) Determine the diameter d against static failure (b) Determine the diameter d against fatigue failure using Goodman approach if D-1.1d...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
Please answer A and B.
The rotating solid stedl shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20. The shaft transmits a torque to point A of TA-340 N m. The shaft is machined from steel with Sy- 420 MPa and Sut-560...
Most questions answered within 3 hours.
-
Calculate the pH of a buffer solution that is
0.116 M in
C2H5NH2
(ethylamine) and 0.403...
asked 1 minute from now -
#include <iostream>
#include <vector>
using namespace std;
class Solution {
public:
vector<int> smallerNumbersThanCurrent(vector<int>&
nums) {
int...
asked 9 minutes ago -
1) What 8 guidelines should you follow to enable you to use
email efficiently and effectively...
asked 13 minutes ago -
What geographical obstacle seems to have taken the longest time
for modern humans to get across?...
asked 18 minutes ago -
When Maria Acosta bought a car 2 and a half
years ago, she borrowed $11,000 for...
asked 26 minutes ago -
package rectangle;
public class Rectangle {
private int height;
private int width;
public...
asked 27 minutes ago -
The Yankee's have a contract with their newly hired manager that
requires a lump sum payment...
asked 47 minutes ago -
A travelling salesman sells milkshake mixing machines and on
average sells 8.9 machines per month. He...
asked 52 minutes ago -
what's the danger in the fact that the market value of a stock
is based on...
asked 1 hour ago -
Describe how do you feel about the post below and
why?
Listening to the podcast reaffirmed...
asked 1 hour ago -
To start an avalanche on a mountain slope, an artillery shell is
fired with an initial...
asked 1 hour ago -
The population of bacteria in a culture can be modeled by P left
parenthesis t right...
asked 1 hour ago