9) A bullet with mass 0.0075 kg is fired with a gun with mass 0.95 kg. The bullet leaves the gun at 380 m/s. a) What is the recoil speed of the gun? Assume the gun was at rest before firing. b) Is the momentum of the bullet greater, smaller or equal (in magnitude) to the recoil momentum of the gun? c) Find both the kinetic energy of the bullet and of the gun. Which is bigger, or are they equal? d) Thinking about your answers to (b) and (c) and about how dangerous the recoiling gun is compared to the fired bullet, reach a conclusion about which quantity (~p or K) is more relevant for the “damage” something can produce.
Please rate the work if you are satisfied with the solution or else kindly ask your doubts or queries in the comment section below
9) A bullet with mass 0.0075 kg is fired with a gun with mass 0.95 kg....
A 1.5 KG gun can fire a bullet 300 mph when the bullet is fired the gun recoil is backwards why does this happen? Calculate the recoil speed is soon as the bullet a shot out
1)A bullet is fired vertically upward from a gun with an initial velocity of 235 m/s. How high does the bullet go? How long does it take to reach its maximum height? How long is it in flight? 2)Calculate the kinetic energy of a 0.350 kg baseball thrown at a velocity of 36.0 m/s.
Momentum and Impulse 2. Your favorite rifle (22 caliber) has a mass of 3.0 kg, a 40 cm long barrel and weigh 2.6 g (a) Before you fire the rifle, how much momentum does the bullet have? (Not a trick question, I hope) (b) Before firing, what is the momentum of the rifle? (c) The bullet is fired with a velocity of 370 m/s. What is the bullet's momentum? (d) With what velocity does the rifle move backwards (Le. recoil)?...
A Styer AMR (Anti-Materiel Rifle) with a mass of 18 kg fires a fires a 20 gram bullet to have a muzzle velocity of 1450 m/s. The average time it takes to reach that muzzle velocity is 0.004 seconds. Since you are holding the gun to keep it horizontal and pushing back on the recoil to keep the AMR stationary.. a) Draw an appropriate momentum diagram for this process... b) And determine the average force you apply to the Styer...
9.) If a bullet of mass 90 grains is fired from a gun at 300 ft/s, what would the value of the physical used has a constant need to be in order to see quantum effects, presuming that instrumentation resolution of 1 picometer. (1 grain = 0.0647 grams, 1 foot = 0.3048 m) 10.)
A bullet of mass 4.3 g is fired horizontally into a 7.4 kg wooden block at rest on a horizontal surface. The coefficient of kinetic friction between block and surface is 0.53. The bullet stops in the block, which slides straight ahead for 1.7 m (without rotation). (a) What is the speed of the block immediately after the bullet stops relative to it? (b) At what speed is the bullet fired?
A bullet with a mass of 4.1 g and a speed of 650 m/s is fired at a block of wood with a mass of 9.6x10-2 kg. The block rests on a frictionless surface and is thin enough that the bullet passes completely through it. Immediately after the bullet exits the block, the speed of the block is 21 m/s. a. What is the speed of the bullet when it exits the block? b. Is the final kinetic energy of...
A bullet of mass 8 g is fired into a 1.2 kg ballistic pendulum (a block of wood acting as the pendulum bob of a thin metal arm attached to a low friction pivot point) that is initially at rest. The bullet exits the block of wood with a speed of 180 m/s and the wooden block swings from its lowest point to a maximum height of 9.2 cm above that location. Determine the velocity of the bullet before it...
A heavy bullet of mass m = 0.1200 kg is fired with an initial
velocity v = 400. m/s into a large block of lightweight wood of
mass M = 0.500 kg, which is initially at rest on a frictionless
surface. This initial situation is depicted on the left side of the
picture below. The bullet gets stuck inside of the wood block and
both move together thereafter as shown in the picture.
a) What is the velocity V of...
In a gun firing test, a 25 gram bullet is shot with a velocity of 500 m/s and embedded into a block which is placed on a trolley, as shown in Figure QI(b). The coefficient of kinetic friction between the block and the trolley is 0.45. The mass of the block and the trolley is 6 kg and 5 kg respectively. The trolley rolls freely on the floor. i. Determine the final velocity of the system. ii. Determine the kinetic...