A tank has a rectangular orifice of 3 ft length and 2 ft height.
The top edge of the orifice
is 8 ft below the water surface. Determine the discharge through
the orifice, treating it as
(a) a small orifice, and (b) a large orifice. Cd = 0.62.
ANSWER :
The answer for the above problem is shown below by hand written notes :
A tank has a rectangular orifice of 3 ft length and 2 ft height. The top...
A rectangular tank with a square base, an open top, and a volume of 884 ft is to be constructed of sheet steel Find the dimensions of the tank that has the minimum surface area n& Let s be the length of one of the sides of the square base and let A be the surface area of the tank. Write the objective tunction A- Type an expression.) The interval of interest of the objective function is tiond (Simplity your...
6. A tank 20 ft long and 10 ft deep is 8 ft wide at the bottom and 18 ft wide at the top. In the bottom is an orifice having an area of 24 84 0.61? in. and å coefficient of discharge of 0.60. If the tank is full at the begin. ning, how long will it take to lower the water surface 6 ft? T
1. Water is poured into a tank of height 1m, width 0.3m and
length 0.3m at a rate of Qin=6x10-5m3/s. An orifice of diameter 6mm
is installed at one side of the tank to discharge the water (Fig.
Q4a). The discharge coefficient is 0.64.
a) When the water level h=0.2m, determine the outflow discharge
rate Qout. Also, determine whether the water level is rising or
falling, and the rate of change of the water level.
b) What is the maximum...
Water flows out of an inverted conical tank with circular
orifice
Solve using MATLAB. Thank you!!
Water flows out of an inverted conical talk with circular orifice at the rate of 4. vy A(y) where r is the orifice radius, y is the height of the water above the orifice, and Avy) is the area of the cross section of the tank at the water level. Suppose r - .1 ft g =-32.17 ft/s, and the tank has an initial...
A rectangular car-top carrier of 2.0-ft height, 5.0-ft length (front to back), and 4.2-ft width is attached to the top of a car. Estimate the additional power required to drive the car with the carrier at 60 mph through still air compared with the power required to driving only the car at 60 mph. Assume that Cp-1.3 for the carrier hp
A rectangular car-top carrier of 2.0-ft height, 5.0-ft length (front to back), and 4.2-ft width is attached to the...
4. A rectangular tank water (width 14.0m, length 14.0m, and height 20 m) is filled with water and open to the atmosphere. The water level in the tank is 1 m below the top of the tank. This tank sits upon a platform of height h. If the water tank is plugged at the bottom so no water is flowing, what is the resultant force exerted by the water on the bottom face of the container? What is the resultant...
A water tank is shaped like a right, circular cylinder with height 6 ft and radius 3 ft. If the tank is filled to 1 ft below the top, find the work required to pump all of the water to the level of the top and let flow over the edge. The density of water is 62.5 lbs per cubic foot.
6) An open top, rectangular tank has sides both equal to 5.0 m and a height of 7.0 m. Initially, it is completely filled with water. A pump removes water from the bottom of the tank at a flowrate (m'/s) of3.2 h?, where h is the height of the water level in meters. Determine the time needed for the water level to drop from 7.0 meters to 3.5 meters. (2 pts)
Tank shown below with orifice 2 inches in diameter located on the side of the tank. a. Determine total energy at the liquid surface in ft. consider orifice as datum. Air: p = 20 lbf/in-abs P. = 14.7 lbf/in2 abs
A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure below. The gate is hinged along its top edge and is held in position by the force P. Friction at the hinge and the weight of the gate can be neglected. Determine the required value of P. Water 29 ft Hinge Gate 60° lb
A rectangular gate having a width of 4 ft is located in the...