My Notes A spool of thread consists of a cylinder of radius R1 = 4.6 cm...
A spool of thread, free to unwind, is on a horizontal surface (with friction) and pulled directly upward (ty) a times. The spool rolls without slipping on the floor. The spool has a mass M, moment of inertia 1, and a radius of R. Assume the string is wrapped around the spool at a radius r (where r <R). 1) Which equation below is a correct expression of Newton's Second Law (XF- ma ) in the x (hortzontal) -direction for...
please answer 8-13
8. A spool of thread has an average radius of 2.00 cm. If the spool contains 75 m of thread, how many turns of thread are on the spool? "Average radius" allows us to not need to treat the layering of threads on lower layers. a. 322 b. 597 c. 150 d. 100 9. In order for a satellite to be geosynchronous, its orbit must: a. be over the equator. b. be over a single longitude. c....
4:36 # $24 OKO 34% A solid cylinder with mass m and radius r rolls without slipping down an incline that makes a 3B" with the horizontal What is the moment of inertia of the solid cylinder about the center of mass? Incorrect I = 2/5.mp Incorrect I = 1/12 + m2 Correct: I = mr/2 Incorrect T = mr2 You are correct. Your receipt no. is 158-399 Previous Tries What form does Newton's 2nd Law take in this system...
Question 9 10 pts A hollow cylinder of outer radius R = 14 cm and mass M = 100 g with moment of inertia about the center of mass Icom = MR2 starts from rest and moves down an incline tilted at an angle 0 = 38° from the horizontal. The center of mass of the cylinder has dropped a vertical distance h= 131 cm when it reaches the bottom of the incline. The coefficient of static friction between the...
A solid uniform cylinder of mass M and radius R is at rest in
the center on a flat slab of mass m and thickness d, which in turn
rests on a horizontal, frictionless table, as shown in the figure at
right below. A horizontal force of magnitude F is applied to the
slab, acting through the center of the slab, causing it to
accelerate to the right. The cylinder rolls without slipping on the
slab. (The direction of F...
A cylinder that has a 39.0-cm radius and is 50.0 cm deep is
filled with air at 20.5°C and 1.00 atm
answer 2 & 3 please.
2. 0/2 points Previous Answers B My Notes A cylinder that has a 39.0-cm radius and is 50.0 cm deep is filled with air at 20.5°C and 1.00 atm as shown in figure (a). The temperature is held constant as a 19.0-kg piston is lowered into the cylinder, compressing the air trapped inside as...
A hollow aluminum cylinder is 2.50 m long and has an inner radius of 2.75 cm and an outer radius of 4.60 cm. Treat each surface (inner, outer, and the two end faces) as an equipotential surface. Part A At room temperature, what will an ohmmeter read if it is connected between the opposite faces? Express your answer with the appropriate units. μΑ ? R= 1.5 • 10-5 Ω Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts...
A thick walled cylinder has a light string
wrapped around its outer radius and rotates
about a horizontal axis. The string then goes
vertically straight up and over a massive
pulley that also rotates about a horizontal
axis, and finally connects to a mass m =
0.900 kg on a rough incline (μk = 0.200) that
is angled at 25.0° to the horizontal.
When the system is released from rest the mass slides down the ramp
a distance of 1.80...
Problem 9.25 Correct A 1.5-kg metal cylinder on a table is placed inside a hoop that is forced at the end of a meter stick. The stick can rolate around a vertical axis that is located 20 cm from the cylinder, as shown in (Figure 1). By exerting a force on the stick, you can make the cylinder rotate in a horizontal plane, with the bottom surface of the cylinder sliding on the rough table. The coefficient of kinetic friction...
In a water pistol, a piston drives water through a larger tube of radius 1.30 cm into a smaller tube of radius 1.10 mm as in the figure below. A diagram shows the interior of a water pistol pointing to the right, and the flow of water through it. The left end of the trigger is connected to the piston on the right end of a cylinder. The left end of the cylinder is connected to a tube, such that...