an aluminum rod and a nickel rod are both 5.00 m long at 20.0 C. The...
an aluminum rod and a nickel rod are both 5.00 m long at 20.0 C. The temperature of each is raised to 70.0 C. What is the difference in length between the two rods?
Homework Answers
Add Answer to:
an aluminum rod and a nickel rod are both 5.00 m long at 20.0 C.
The...
A brass rod is 69.5 cm long and an aluminum rod is 49.3 cm long when...
A brass rod is 69.5 cm long and an aluminum rod is 49.3 cm long when both rods are at an initial temperature of 0
Two circular rods, one steel and the other copper, are both 0.780 m long and 1.50...
Two circular rods, one steel and the other copper, are both 0.780 m long and 1.50 cm in diameter. Each is subjected to a force with magnitude 4500 N that compresses the rod. What is the difference in the length of the two rods when compressed?
A copper rod and an aluminum rod of the same length and cross-sectional area are attached...
A copper rod and an aluminum rod of the same length and cross-sectional area are attached end to end. The copper end is placed in a furnace which is maintained at a constant temperature of 292∘C. The aluminum end is placed in an ice bath held at constant temperature of 0.0∘C. Calculate the temperature (in degrees Celsius) at the point where the two rods are joined. The thermal conductivity of copper is 380 J/(s⋅m⋅C∘) and that of aluminum is 200...
A copper rod and an aluminum rod of the same length and cross-sectional area are attached...
A copper rod and an aluminum rod of the same length and cross-sectional area are attached end to end (Figure 1). The copper end is placed in a furnace maintained at a constant temperature TCu = 230 ∘C . The aluminum end is placed in an ice bath held at a constant temperature of 0.0∘C. Calculate the temperature at the point where the two rods are joined.
Part A Abrass rod is 700 cm long and an aluminum rodis 500 cm long when...
Part A Abrass rod is 700 cm long and an aluminum rodis 500 cm long when both rods are at an emperor of O'C. The rods are placed innehage of 12 cm bent, as shown in the fire. The the ends of the roos is mind 120.0 cm thoughout. The temperature of both roos is regulhey are barely in. Al whatemperature de contact our? The counts of a prof brass and are 20x105cbrass) and 24 x 10 caluminum -120.0 cm...
A copper rod and an aluminum rod of equal diameter are joined end to end in...
A copper rod and an aluminum rod of equal diameter are joined end to end in good thermal contact. The temperature of the free end of the copper rod is held constant at 100°C, and that of the far end of the aluminum rod is held at 0°C. If the copper rod is 0.80 m long, what must be the length of the aluminum rod so that the temperature at the junction is 50°C?
A copper rod and an aluminum rod of equal diameter are joined end to end in...
A copper rod and an aluminum rod of equal diameter are joined end to end in good thermal contact. The temperature of the free end of the copper rod is held constant at 100°C, and that of the far end of the aluminum rod is held at 0°C. If the copper rod is 0.74 m long, what must be the length of the aluminum rod so that the temperature at the junction is 50°C? __________________m
An aluminum rod has a resistance of 3.12 Ohm at 20.0 degree C. Calculate the resistance...
An aluminum rod has a resistance of 3.12 Ohm at 20.0 degree C. Calculate the resistance of the rod at 120 degree C by accounting for the changes in both the resistivity and the dimensions of the rod. The coefficient of linear expansion for aluminum is 2.40 times 10^-5 (degree C)^-1. Ohm
An aluminum rod is 30cm long at 33°C and has a mass of 330g. If 13,000...
An aluminum rod is 30cm long at 33°C and has a mass of 330g. If 13,000 J of energy is added to the rod by heat, what is the change in length of the rod?
A brass rod with a length of 1.50 m and a cross-sectional area of 2.50 cm2...
A brass rod with a length of 1.50 m and a cross-sectional area of 2.50 cm2 is fastened end to end to a nickel rod with length L and cross-sectional area 0.880 cm2 . The compound rod is subjected to equal and opposite pulls of magnitude 3.46×104 N at its ends. a.Find the length L of the nickel rod if the elongations of the two rods are equal. b.What is the stress in the brass rod? c.What is the stress...
Part A Abrass rod is 700 cm long and an aluminum rodis 500 cm long when both rods are at an emperor of O'C. The rods are placed innehage of 12 cm bent, as shown in the fire. The the ends of the roos is mind 120.0 cm thoughout. The temperature of both roos is regulhey are barely in. Al whatemperature de contact our? The counts of a prof brass and are 20x105cbrass) and 24 x 10 caluminum -120.0 cm...
An aluminum rod has a resistance of 3.12 Ohm at 20.0 degree C. Calculate the resistance of the rod at 120 degree C by accounting for the changes in both the resistivity and the dimensions of the rod. The coefficient of linear expansion for aluminum is 2.40 times 10^-5 (degree C)^-1. Ohm
Most questions answered within 3 hours.
-
On May 1, First Bank perfected a security interest in Debtor’s
inventory. On June 1, Bob...
asked 26 minutes ago -
A new kind of typhoid shot is being developed by a medical
research team. The old...
asked 2 hours ago -
Write a chemical equation for these reactions. (Use
the lowest possible whole number coefficients.) Include
states-of-matter...
asked 3 hours ago -
For each of the Z-scores below, determine two probabilities
(show four three decimal places): (1) the...
asked 4 hours ago -
Oxidative phosphorylation is achieved through chemiosmotic
coupling, which turns chemical energy into osmotic potential energy
that...
asked 7 hours ago -
Hollywood Shoes would like to maintain their cash account at a
minimum level of $64,000, but...
asked 7 hours ago -
Proteins CtrA-P, DnaA, and GcrA behave similarly to what
molecule in the Eukaryotic Cell Cycle?
asked 7 hours ago -
TRUE OR FALSE
In case of a competitive tender procedure, in the request for
quotation, the...
asked 7 hours ago -
I am a little behind please provide some explanation, will
provide thumbs up.
This question considers...
asked 7 hours ago -
Let say the utility function as U(X,Y) = lnX + Y. Show that the
marginal rate...
asked 7 hours ago -
A current of I=8.0A is flowing in a typical extension cord of
length L=3.00m. The cord...
asked 7 hours ago -
1. When balancing the equation H2SO4 (aq) + NaOH (aq) →
Na2SO4(aq) + H2O(aq), would you...
asked 8 hours ago