Please solve whole this problem and be clear when you write by your hand.
2. An audio frequency signal 10sin2π500t) is used to amplitude modulate a carrier of 50sin(2π 100...
below is used to modulate a carrier to generate the AM signal yt) (Am()) cos(1000t) The periodic signal m() shown a) The power efficiency of the system is measured to be 1 () The type of AM modulation, i.e. SSB, DSBSC, (i) The constant A. (ili) The modulation index 1/13. Determine DSB with carrier enit -3 b) An angle modulated signal is given by d(t-2 cos (2n1061+ sin 2 1000). Find i) The carrier frequency. ii) The baseband signal bandwidth....
1 2 4. The amplitude modulation signal is given by the following expression and is applied to 75 load. Vam(t) = 10 sin (21fct) - 2.5 cos (1500krt) + 2.5 cos (1450krt) V Determine: a) Modulation index b) The frequency of the carrier and the information signal c) The bandwidth d) The total power e) The transmission power efficiency be ar e 5. One of the inputs to a frequency modulator is a 250 kHz carrier signal with amplitude of...
This question should be solved by MATLAB. - Generate an analog signal. (This should be an audio, any audio can be used.) - Analyze frequency spectrum of this analog signal. - Modulate it. (AM Modulation can be used) - Send the modulated signal over a wireless channel. (Before sending the signal, a noise should be added.) Thank you already for your help!
A carrier signal c(?) = ? cos(??) is modulated by a single-tone signal ?(?) = ? ???(??) to form the AM signal: s(t)= [? + ????(??)]???(??), where ? = 10, ? = 2, ? = 1000 ??, ? = 50 ??. a- Obtain an expression for the sidebands of ?(?). b- Sketch ?(?) c- Sketch the spectra |?(?)|, |?(?)|, |?(?)| against f. d- Calculate the modulation index (m) e- What bandwidth is required to transmit the AM signal. f- Show...
An information signal is of the form s(t) = sin(2*pi*t)/t. The signal amplitude modulates a carrier of frequency 10Hz. Find and sketch the Waveform and Fourier transform of the transmitted signal before and after AM modulation. For AM modulation you can consider the simple case of DSB format (or double-sideband suppressed carrier modulation).
A message m(t) sinc2 (M) cos (2π9t) is used to modulate a carrier to produce an LSB-AM signal. (a) Find and sketch the spectrum of m(t); determine and sketch the spectrum of mh (t) graphically; determine m,(t) by finding the inverse Fourier transform of the previous spectrum; determine the LSB-AM message signal expression. (b) Sketch the spectrum of the DSB-SC signal 2m(t) cos 2mfet; remove the upper sideband and sketch the resulting LSB spectrum; determine the LSB-AM message signal expression...
Consider an AM system. The message signal is given by cos(1000t) volts. The modulated signal is (0.5+acos(1000m))cos(2π.) volts, where α is a positive coefficient, and fe is the carrier frequency. (a) Determine the value of α when the modulation index is 100%. (b) Determine the value of α when the modulation index is 50%. (c) Determine the value of α when the modulation index is 200%. (6 marks) Continue from (1) and suppose α-05. Sketch the spectrum of the transmitted...
an expression nM() for an AM signal with a carrier frequency of 2 MHz that conveys a 1. (a) Write down sine wave message whose frequency is 2 peak-to-peak amplitude is 70 Volts. 500 Hz. The AM signal's modulation index is 0.75 and its (b) Compute the power efficiency n of this signal.
A 1.5 MHz carrier frequency is amplitude-modulated by a 200 kHz sinewave audio signal. The bandwidth would be A. 40 kHz. B. 405 kHz. C. 4,000 kHz. D. 400 kHz.
An AM receiver is tuned to broadcast station at 600 kHz. Calculate the image rejection in dB, assuming that the input filter consist of one tuned circuit with a Q of 40? An SSB system transmit a peak envelope power of 100 W into a 75 ohms load. The carrier signal is modulated by two tones, with frequencies 2 kHz and 3 kHz with equal magnitude and only the lower sideband is transmitted with a suppressed carrier. Determine the average...