A 65 deg AOB level coordinated turn will result in what normal load factor?
a. 2.0 g
b. 3.0 g
c. 2.4 g
d. 4.5 g
c. 2.4 g
Explanation: If you turn in a coordinated bank of 65 degrees, you will feel an increase of Gs of 1 / cos(65) or 2.366 Gs =2.4
A 65 deg AOB level coordinated turn will result in what normal load factor?
Liquid Level 1. You are using a 1 turn rotatory potentiometer to design a level sensor to measure liquid level on a tank. The total resistance of the potentiometer R = 10K and the output voltage that is measured by an Arduino is IV. Find the angle of turned in the potentiometer as well as the height of liquid level in the tank. 2. A platinum resistance coil is to be used as a temperature sensor (Rthermal) and has a...
Maximum Marks:100 a) Define load factor. b) What do you know about diversity factor? c) Explain load duration curve and its utility. d) What are the major Components of Thermal Power Station? Give the names and their function.
A cart of weight 60 N is accelerated across a level surface at 0.15 m/s2. What net force acts on the cart? (g = 9.8 m/s2) a. 3.0 N b. 0.92 N c. 0.31 N d. 4.5 N
1) For the loading of the beam shown below, determine the maximum normal and shear stress at the wall if Kt for bending is 2.7 and K, for torsion is 2.3 If we use a steel with an Sy 600 MPa, what is the "safety factor" if we only consider the maximum normal stress? Notice the bending moment, start with a cross product to determine the moment at the wall. The vector R-[0.25,0,0.3] in meters 200 mm 25-mm-dia. round rod...
C) is this an inductive or capacitive load? why?
d) what is the power factor of the load.
1. The Y-Y three phase balanced system has the following parameters. (30pts) Vo_an/bn/cn = 12Vrms Lo=3mH Ro=5k2 RLINE =8k2, Freq = 300KHz. RLOAD =20k.2 LLOAD=9mH CLOAD =0.001uF RLINE_A RLOAD_A Roa La LLOAD_A CLOAD A N CLOAD_BY CLOAD_C Vb bn LLOAD_C LC LLOAD_B Ro C HRLOAD_C RLINE_B Ro B RLOAD_B RLINE_C
answer 1
b) there is u lovu 4. In a spring experiment, the results were: Load (N) 0 1 2 3 4 5 6 7 Length (mm) 50 58 70 74 82 90 102 125 Extension (mm) a) What is the length of the spring when unstretched? b) Copy and complete the table. c) Plot a graph of extension : load. d) One of the results is wrong. Which is it? What do you think it should be? e) Mark...
Phase, TTT, and CCT diagrams provided
6.8. The heat treatments noted below are carried out in 1080 steel. In each case what phases will be present at the end of the treatment? a. Austenitize at 750 deg C; quench to 0 deg C in 1s. b. Austenitize at 750 deg C; rapid quench to 650 deg C; isothermally anneal for 1000 s; quench to 0 deg C in 1s c. Austenitize at 750 deg C; very rapid quench to 250...
26 27
26) By what amount does the intensity level increase when you triple the power to the source of sound? A)4.8 dB B) 6.0 dB C) 9.5 dB D) 3.0 dB E) 12 dB 27) A transverse wave traveling along a string transports energy at a rate P. If we want to double this rate, we could A) increase the amplitude of the wave by a factor of 2 B) increase the amplitude by a factor of2 C) increase...
Question 7 1.33 pts Which types of physicians listed below are Specialists: (Level O a. All internists b. Psychiatrists O c. All pediatricians O d. a, b and Oe. None of the above Question 8 1.33 pts The first hospitalists were trained: (Level 1) a. During the preindustrial period b. During the industrial period c. Both a and be d. None of the above Question 6 1.33 pts Some differences between allopathic and osteopathic physician include: (Level 2) O a....
What type of molecular-level collisions result in products? Group of answer choices: A) High-energy collisions B) High-energy, high-temperature collisions C) None of the above D) Low-energy, directed collisions