Homework Answers
Add Answer to:
2. A component has a fluctuating stress of σ() = 120MPa + 120MPa sin(t). The stress is due to ben...
2. A component has a fluctuating stress of σ() = 120MPa + 120MPa sin(t). The stress...
2. A component has a fluctuating stress of σ() = 120MPa + 120MPa sin(t). The stress is due to bending and the material is AlSl 1060 HR. There is a groove cut in the part such that Kt=1.8. The minimum shaft diameter is 2cm and the notch radius is 3mm. a. Determine the endurance limit and all associated Marin factors b. Determine the factor of safety for infinite life using the Goodman Failure c. If the factor of safety is...
A rotating shaft is made of AISI 1035 CD steel is subjected to an axial load of 710N
A rotating shaft is made of AISI 1035 CD steel is subjected to an axial load of 710N, a fluctuating torque load from 60 to 120 N.m, and a completely reversed bending moment of 160N.m. The shaft has a diameter of 30mm, and operates at T=250°C, and has a life reliability of 95%. Note that the fatigue stress-concentration factor for bending Kfb is 1.49 and that for torque Kft is 2.65..1. Draw the Yield (Langer) line 2. Modified Goodman line. 3. Calculate...
: A 1 in-diameter solid round bar has a groove with a 0.1-in radius machined into...
: A 1 in-diameter solid round bar has a groove with a 0.1-in radius machined into it. The bar is made of steel with an ultimate strength of 120 ksi and it is subjected to an axial force that fluctuates between-5.15 kip and 12.85 kip. The static stress concentration factor at the groove is Kt 2.1. (40 points) a) Classify the problem type based on the loading condition. b) Determine the fatigue factor of safety using the Goodman failure criterion....
The stepped shaft shown at right has constant bending moment of 40 N.m at the step
1) The stepped shaft shown at right has constant bending moment of 40 N.m at the step, transmits 75 N.m constant torque and rotates at constant 500 rpm. The shaft was machined from 1040 cold-rolled steel with D = 22.8 mm, d = 19 mm and r = 1.9 mm. Determine fatigue factor of safety for infinite life with reliability of 99%. Use Case 3) Goodman failure and ignore Neuber notch sensitivity. 2) Check factor of safety for fatigue failure of...
In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A= 400 lbr
In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A= 400 lbr .and at C = 800 Ibr. These radial forces are caused by spur gears mounted to shaft (a result of the pressure angle of the teeth, 20 degrees) that mesh with 2 other spur gears, not shown. Also, The shaft transmits a constant torque of 11110 in-lbr (925 ft-lbr) due to the tangential force (Wt: transmitted load) at C of...
A 1045 hot rolled steel rod undergoes axial cyclic loading from a minimum stress of 2...
A 1045 hot rolled steel rod undergoes axial cyclic loading from a minimum stress of 2 kpsi to a maximum of 10 kpsi. The rod has a hole in the center of bar, with a Kt 1.7, and notch sensitivity factor 0.9. The yield strength of bar is 45 kpsi, ultimate strength 82 kpsi, fully endurance limit of 20 kpsi, fatigue strength fraction 0.85. 1. a. Using modified goodman criteria, find FOS b. lfinfinite life is not predicted estimate the...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diam...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
A 2-in. diameter solid round bar has a groove machined on its surface (see Page 1046...
A 2-in. diameter solid round bar has a groove machined on its surface (see Page 1046 in the textbook) The radius of the groove is 0.1 in. The bar is loaded in cyclic bending that causes the bending moment at the groove to fluctuate between 0 and 25,000 lb.in. The bar material is a hot-rolled SAE 1095 steel Using the Goodman criterion, determine the factor of safety for infinite life.
Problem 2: A hot-rolled shaft shoulder has a large diameter D is 45 mm, the small...
Problem 2: A hot-rolled shaft shoulder has a large diameter D is 45 mm, the small diameter d is 30 mm, and the fille (notch) radius is 3 mm. The bending moment, and the steady torsion moments are 100 N.m, and 75 N. respectively. The reliability goal for the endurance limit is 0.90. If the shaft is made of AISI 1030 hot-roll steel, (a) Determine the fatigue stress concentration factors (Ks, and Ks). (b) Determine endurance limit (Se). (c) Determine...
doesn't need any extra information, everything is in there indi 2.. In the figure shown, shaft...
doesn't need any extra information, everything is in
there
indi 2.. In the figure shown, shaft A, made of AISI 1020 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite forces F via shaft B. A theoretical stress-concentration factor Kts of 1.6 is induced in the shaft by the -in weld fillet. The length of shaft A from the fixed support to the connection at shaft B is 2 ft. The load...
2. A component has a fluctuating stress of σ() = 120MPa + 120MPa sin(t). The stress is due to bending and the material is AlSl 1060 HR. There is a groove cut in the part such that Kt=1.8. The minimum shaft diameter is 2cm and the notch radius is 3mm. a. Determine the endurance limit and all associated Marin factors b. Determine the factor of safety for infinite life using the Goodman Failure c. If the factor of safety is...
: A 1 in-diameter solid round bar has a groove with a 0.1-in radius machined into it. The bar is made of steel with an ultimate strength of 120 ksi and it is subjected to an axial force that fluctuates between-5.15 kip and 12.85 kip. The static stress concentration factor at the groove is Kt 2.1. (40 points) a) Classify the problem type based on the loading condition. b) Determine the fatigue factor of safety using the Goodman failure criterion....
A 1045 hot rolled steel rod undergoes axial cyclic loading from a minimum stress of 2 kpsi to a maximum of 10 kpsi. The rod has a hole in the center of bar, with a Kt 1.7, and notch sensitivity factor 0.9. The yield strength of bar is 45 kpsi, ultimate strength 82 kpsi, fully endurance limit of 20 kpsi, fatigue strength fraction 0.85. 1. a. Using modified goodman criteria, find FOS b. lfinfinite life is not predicted estimate the...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
A 2-in. diameter solid round bar has a groove machined on its surface (see Page 1046 in the textbook) The radius of the groove is 0.1 in. The bar is loaded in cyclic bending that causes the bending moment at the groove to fluctuate between 0 and 25,000 lb.in. The bar material is a hot-rolled SAE 1095 steel Using the Goodman criterion, determine the factor of safety for infinite life.
Problem 2: A hot-rolled shaft shoulder has a large diameter D is 45 mm, the small diameter d is 30 mm, and the fille (notch) radius is 3 mm. The bending moment, and the steady torsion moments are 100 N.m, and 75 N. respectively. The reliability goal for the endurance limit is 0.90. If the shaft is made of AISI 1030 hot-roll steel, (a) Determine the fatigue stress concentration factors (Ks, and Ks). (b) Determine endurance limit (Se). (c) Determine...
doesn't need any extra information, everything is in
there
indi 2.. In the figure shown, shaft A, made of AISI 1020 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite forces F via shaft B. A theoretical stress-concentration factor Kts of 1.6 is induced in the shaft by the -in weld fillet. The length of shaft A from the fixed support to the connection at shaft B is 2 ft. The load...
Most questions answered within 3 hours.
-
This java code won't run and I can't figure out the problem with
it. Please help...
asked 40 minutes ago -
Trace the following recursive methods:
a) isPal with the string “abccda”
b) isAnBn with the string...
asked 1 hour ago -
1. Which of the following is false about photosynthesis?
A. ATP is the molecule used to...
asked 2 hours ago -
A simple random sample of size n=64 is obtained from a
population with a mean of...
asked 3 hours ago -
(2 dimensions, 1 object, 2 accelerations)
1) A projectile is thrown with a wind. The wind...
asked 4 hours ago -
Brian makes $34,100 per year. How much can Brian expect to
contribute to FICA taxes in...
asked 5 hours ago -
To buy a new house you must borrow $155,000. To do this you take
out a...
asked 5 hours ago -
Spacely Sprockets is evaluating the construction of a new plant
on land the company purchased for...
asked 6 hours ago -
1. Consider a linear regression model of y on K regressors and
an intercept.
(i) Describe...
asked 6 hours ago -
Enter a balanced equation for the reaction between hydrochloric
acid and sodium sulfite.
Express your answer...
asked 6 hours ago -
Give a regular expression describing the language
{x | x ∈ Σ* and x does not...
asked 6 hours ago -
Masses of 1.0 kg, 2.0 kg, and 3.0 kg are each separately subject
to a net...
asked 6 hours ago