1. (a) Using the minimum 2-level SoP logic required, design a sequential circuit with three T fli...
ECE 260 HW 7 NAME 1. A sequential circuit has two JK flip-flops A and B, two inputs X and Y, and one output Z. The flip-flop input equations and circuit output equation are: (a) Draw the sequential circuit (b) Derive the state equations for Q and Q (c) Construct the state/output table (d) Draw the state diagram Note, for JK flip-flop: Q1O+KQ Design a sequential circuit with two JK flip-flops A and B and two inputs E and F....
1. Design a 3 bit sequential circuit using T flip flops and one input X. When X = 0 the state of the circuit remains the same. When X = 1 the circuit goes through state transition from 0 -> 6 -> 2 -> 3 -> 5 -> 0. Make the state table, state equation and state diagram. Need help trying to understand how to set up the truth table, should I use a JK truth table and go on...
b) A sequential circuit is constructed with one T flip-flop A, one D flip-flop B and one input X, when X=0, the state of the circuit remains the same.When X=1, the circuit goes through the transitions from 00 to 01 to 11 to 10 back to 00, repeat. (i) Draw the state transition diagram (ii) Construct the state Table (iii) Draw the circuit.
How to design a sequencial circuit with two JK flipflop A&B and two inputs E &F. If E = 0, the circuit remains inthe same state regardless of the valueof F. When E=1 and F=1, thecircuit goes through the state transition from 00 to 01, to 10, to11, and back to 00, and repeats. When E=1 and F=0, the circuitgoesthrough the state transition fro 00 to 11, to 10, to 01, back to 00and repeats.(This problem is actually from Digital...
Based on this grouping use AND and OR gates, find the minimum circuit to realize a 2-level logic SoP circuit of a b 00 01 11 10 01 00 0 1 11 000 10 0 0 1 4AND&1OR Gates w/ total of 14 inputs 4OR&1AND Gates w/ total of 16 inputs 4AND& 1OR Gates w/ total of 16 inputs 4OR&1 AND Gates w/ total of 14 inputs
Based on this grouping use AND and OR gates, find the minimum circuit...
Q2) [7 Marks] [CLO 2.02] For the state diagram shown, design the circuit using T flip flops. The input and output are shown on the transition arrows as Input/Output. 000 11 0/0 010 0/0 0/0
9. (10%) A Mealy sequential circuit has five states; one input x, and one output y. Its state diagram is shown in the following figure. (a) (5%) Design the circuit with D flip-flops by treating the unused states as don't-care conditions. (b) (5%) Following (a), analyze the circuit obtained from the design to determine the effect of the unused states. 0/0 001 0/0 1/0 011 0/0 100 0/0 010 0/0 1/1 000
When using the K-map to find the equations for DA and DB for the problem down below, how can you tell which variable is supposed to be for the row and columns? How can I tell if the rows for the 2x4 k-maps would be dealing with "A" while the columns would be dealing with "Bx"? Does it even matter how I set up the K-map? --------------------------------------------------------------------------------------------------------------------------------------------------------- Design a sequential circuit with two D flip-flops A and B, and one...
Please make the circuit
Design a Mealy sequential circuit (Figure 16-27) which investigates an input sequence X and will produce an output of Z 16.8 1 for any input sequence ending in 0011 or 110 Example: X 101001 1 00 11 Z 0 00 0 001 1 0 0 1 Notice that the circuit does not reset to the start state when an output of Z1 occurs. However, your circuit should have a start state and should be provided with...
3. Implement a Sequential Circuit using JK Flip Flops and any
logic gates to perform like the state diagram shown below.
X=1 YO X=0 X1 Problem 3