NOTE :
a) If you find the solution doubtful or doesn't match with your answer provided, or you feel that I am wrong by any means feel free to mention that in comment. Otherwise your downvote will keep me in doubt. So that i can correct myself and it will also help me in future to guide others.
b) Please re-check the calculation and inform me if there is any error. Happy to help.
c) Some feedbacks or rating will help me to improve myself. Wish you all the best. Happy Learning. Thank You.
2. A Wind Resource Manual for a wind turbine installation candidate site lists, among others, the...
1. Consider a wind turbine of diameter 52 m, rated capacity 850 kW, installed at a site where the average wind power density = 700 W/m2. The total energy output over a year = 3240 MWh. What is the average power output ?
1. Consider a wind turbine of diameter 52 m, rated capacity 850 kW, installed at a site where the average wind power density = 700 W/m2. The total energy output over a year = 3240 MWh. What is the specific rated capacity of the wind turbine (in the units commonly specified).
2. A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air...
1. Consider a wind turbine of diameter 52 m, rated capacity 850 kW, installed at a site where the average wind power density = 700 W/ m2. The total energy output over a year = 3240 MWh. What is the capacity factor?
1 1. Consider a wind turbine of diameter 52 m, rated capacity 850 kW, installed at a site where the average wind power density = 700 W/m2. The total energy output over a year = 3240 MWh. What is the proportion of wind energy captured? a
. A typical commercial wind turbine costs approximately $2 million per MW of installed power and requires 5.76 TJ per million dollars of energy to manufacture the wind turbine. (a) Calculate the amount of energy that is consumed (i.e. energy invested) in the manufacture ofa 1.5 MW wind turbine, assuming that turbine manufacture requires 5.76 TJ per million dollars spent. (TJ Tera-joules 1012 joules) (b) If the wind turbine has blades that are 40 meters (radius) long and the average...
If the average power density for large scale wind turbine is 2 W/m2 , what will be the area required for the wind turbines with total energy of 4 TW ( 1 TW = 1012 W , that is, one terawatt is equal to one trillion watt;1kilometer=1000meter Question 42 options: 1 million (Km)2 1.5 million (Km)2 1.7 million (Km)2 2.0 million (Km)2 2.2 million (Km)2
MIET 2480-Renewable Energy Systems-15 Jun 2019 Quiz 2: Wind Power Adeol Summanleknl Name: Student ID: 1. You have a wind site with average wind speed of 8.2 m/s over 1 year, how the average power density in the wind is calculated, given density of the wind as 1.225 kg/m3? a. (1.225) (8.23) -338 W/m2 b. The estimated value closest to the actual average power density is calculated knowing the wind speed frequency distribution fi for each wind speed vi measured...
1. 1. The primary energy savings in tep (1 MWh -0.086 tep) and diesel, which involves the direct use of heat from a geothermal resource to cover a heat demand of 100 kW for 3,500 h / year, assuming that this demand will be covered with diesel boiler of average yield 0.8 (for diesel 1.12 tep/ton gas oil), they are: a) 30.1 tep/year, 26.9 ton/year b) 37.6 tep/year, 33.6 ton/year c)41.2 tep/year, 36.8 ton /year 1. 2. A hydraulic pump...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...