For a square 50x50 mm cross-section find the maximum tensile and compressive stress, if P-9.5 kN....

Question

Question

Please good hand writing I will rate

Answer 1

Answer #1

50 mm 2. 2一 1o 12o e. -49-3 м po- 너 3035 ho 45go

Answer 2

Similar Homework Help Questions

P = 20 kN. Calculate the following: 1. The maximum tensile and compressive stresses at the...

P = 20 kN. Calculate the following: 1. The maximum tensile and compressive stresses at the base of the mast A 2. The maximum tensile and compressive stresses at point B of the mast For each stress state at A and B indicate which side of the mast experiences tension and which side experiences compression. 0.25 m m D w 3 m H С. - 0.1 m mast cross section 3 m 60° Р B 584 mm 6 m mast...
5) Find the moment M, if the maximum tensile stress in the T shape cross section...

5) Find the moment M, if the maximum tensile stress in the T shape cross section js 1 ksi. Determine the maximum compressive stress. 7) a-a is 10 in wide and 6 in deep. Determine maximum tensile and comoressive stress on a-a Find the moment M, if the maximum tensile stress in the T-shape cross section is 1ksi. Determine the maximum compressive stress. 2 in 10 in 2 in 4 in -1 in 1 inz 2 in 11 in 2...
5) Find the moment M, if the maximum tensile stress in the T shape cross section js 1 ksi. Determ...

5) Find the moment M, if the maximum tensile stress in the T shape cross section js 1 ksi. Determine the maximum compressive stress. 7) a-a is 10 in wide and 6 in deep. Determine maximum tensile and comoressive stress on a-a Find the moment M, if the maximum tensile stress in the T-shape cross section is 1ksi. Determine the maximum compressive stress. 2 in 10 in 2 in 4 in -1 in 1 inz 2 in 11 in 2...

Compute the maximum tensile and compressive bending stress for the cantilever beam with uniform load w = 65 kN/m and the cross-section shown below.

Compute the maximum tensile and compressive bending stress for the cantilever beam with uniform load w = 65 kN/m and the cross-section shown below.
use this formulas $50 kNm Determine the maximum compressive and tensile normal stress in the cross-section...

use this formulas $50 kNm Determine the maximum compressive and tensile normal stress in the cross-section shown in the figure. 10 cm 15 cm 10 cm 15 cm 50 kNm Determine the maximum normal stress in the cross-sect 10 cm 15 cm 10 cm 15 cm T.C. PIRI REIS UNIVERSITY, ENGINEERING FACULTY Formulae and Constants Relations between w, V.M Torsion dV(x) = (x), NGUV) Shear stress in shaft with circular cross-section: where Axial Load for solid cross-section, for tubular cross...
Q211 A steel beam has Z-bar cross section as shown in below. Here O is the...

Q211 A steel beam has Z-bar cross section as shown in below. Here O is the centroid of the cross section Moment of inertia and product of inertia of the cross section are given by I, = 24.3960(10° ) mm. l, = 67.41 10(10° ) mm. 1,--30.1840(10° ) mm. The internal force developed in the cross section is M 12 kN-m as shown. Determine the location and magnitude of the maximum tensile stress and maximum compressive stress in the cross...

A bar of 15mm x 15mm square cross-section is machined so as to reduce the thickness...

A bar of 15mm x 15mm square cross-section is machined so as to reduce the thickness in a central region to 5mm, as shown in Figure 5. The bar is now subjected to a force F=2kN whose line of action passes through the centroid of the original square section. Sketch the distribution of stress in the reduced section and find the maximum tensile stress. By what factor does this exceed the average normal stress in the original section? 6. A...
2 KNm 8 kN·m 30 mmA 150 mm 150 ma FIND a) Sketch the shear and...

2 KNm 8 kN·m 30 mmA 150 mm 150 ma FIND a) Sketch the shear and moment diagrams. b) Determine the maximum tensile stress on a cross section just to the left of B, where the 8 kN m couple acts. c) Determine the maximum compressive stress o on a cross section just to the left of B d) Determine the absolute maximum bending stress in the beam and draw the stress distribution over the cross section at this point.
Find the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: w...

Find the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: w = 13 kN/m L = 9 m b = 93 mm h = 193 mm Ensure that your answers are in MPa. w IIIIIIIIII Cross-Section:

A beam of rectangular cross section 200 mm deep and 100 mm wide. If the beam...

A beam of rectangular cross section 200 mm deep and 100 mm wide. If the beam is 3m long, simply supported at either end and carries point loads as shown in FIGURE 2 (on page 4). 2. SAN 1OAN R, FR 100mm FIG.2 (a) Calculate the maximum bending moment (b) Calculate the maximum stress in the beam (c) At the point of maximum stress sketch a graph of the stress distribution through the thickness of the beam, indicating which are...