Homework Answers
Add Answer to:
Deliverable 2 Construct a fin of AIS1304 in Solidwork (a single cylinder) with D-0.02 m and L 0.0...
It's a heat transfer question. The chip is square with dimensions 15mm by 15mm and 5mm...
It's a heat transfer question. The chip is square with dimensions 15mm by 15mm and 5mm thickness with constant temperature Tc = 87 degrees C. At the top surface, 20 pin fins with convective ends are attached to the chip. The diameter of each fin, Dp = 1.5 mm, the length of each fin, Lp = 15 mm, and the thermal conductivity Kp = 400W/mK (For chip and fins). The convection coefficient, h = 50 W/(m2·K), and fluid temperature of...
It's a heat transfer question. The chip is square with dimensions 15mm by 15mm and 5mm...
It's a heat transfer question. The chip is square with dimensions 15mm by 15mm and 5mm thickness with constant temperature Tc = 87 degrees C at the bottom of the chip. At the top surface, 20 pin fins with convective ends are attached to the chip. Above the chip, we have the 20 fins plus we also have the exposed board area, which is total area of the chip minus the base area of the 20 fins. The diameter of...
It's a heat transfer question. Please do not copy from others, thank you. The chip is...
It's a heat transfer question. Please do not copy from others, thank you. The chip is square with dimensions 15mm by 15mm and 5mm thickness with constant temperature Tc = 87 degrees C at the bottom of the chip. At the top surface, 20 pin fins with convective ends are attached to the chip. Above the chip, we have the 20 fins plus we also have the exposed board area, which is total area of the chip minus the base...
Consider a rectangular fin (k = 180 W/m-K) of length L =10 mm, thickness i =1...
Consider a rectangular fin (k = 180 W/m-K) of length L =10 mm, thickness i =1 mm, and width w» t. The base temperature of the finis Ty = 150°C, and the finis exposed to a fluid of temperature T, =25°C. Assuming a uniform convection coefficient of h = 110 W/m2.K over the entire fin surface, determine the fin heat transfer rate per unit width 4; efficiency ng: effectiveness es, thermal resistance per unit width and the tip temperature T...
please show derivation of the nodal equations and how to create the graphs. A straight fin...
please show derivation of the nodal equations and how to create
the graphs.
A straight fin of uniform cross section is fabricated from a material of thermal conductivity 50 W/m*K, thickness w 6mm, and length L-48mm, and is very long in the direction normal to the page. The convection heat transfer coefficient is 500 W/m2 *K with the ambient air temperature of T-30C. The base of the fin is maintained at Tb = 100C, while the fin tip is will...
Problem 3: Ordinary Differential Equations A straight fin of uniform rectangular cross section (0.5 mm x...
Problem 3: Ordinary Differential Equations A straight fin of uniform rectangular cross section (0.5 mm x 100 mm) with a length (L) of 5 cm is attached to a base surface of temperature 110°C (T). The surface of the fin is exposed to a cooling fluid at 20°C (T) with a convection heat transfer coefficient (h) of 15 W/(m²K). The conductivity (k) of the fin material is 400 W/(m.K). (a) Plot the temperature profile along the length of the fin,...
1) 2) 3) PROJECT #1 (2.5 Marks): The heat that is conducted through a body must...
1)
2)
3)
PROJECT #1 (2.5 Marks): The heat that is conducted through a body must frequently be removed by other heat transter processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width Z 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature 1. The conductivity of the aluminum...
The heat that is conducted through a body must frequently be removed by other heat transfer...
The heat that is conducted through a body must frequently be removed by other heat transfer processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature T. The conductivity of the aluminum fin (k) and coefficient of heat convection of...
4. A silicon chip is attached with a copper pin fin in order to enhance the...
4. A silicon chip is attached with a copper pin fin in order to enhance the heat transfer. The square shape silicon chip has a width of W=10 mm on each side. The length and diameter of the copper pin are L=20 mm and D=4 mm, respectively. During the operation, the surface of the chip, as well as the base of the pin, are maintained at the temperature of To=375 K. The thermal conductivity of the copper pin fin is...
4. A silicon chip is attached with a copper pin fin in order to enhance the...
4. A silicon chip is attached with a copper pin fin in order to enhance the heat transfer. The square shape silicon chip has a width of W=10 mm on each side. The length and diameter of the copper pin are L=20 mm and D=4 mm, respectively. During the operation, the surface of the chip, as well as the base of the pin, are maintained at the temperature of To=375 K. The thermal conductivity of the copper pin fin is...
Consider a rectangular fin (k = 180 W/m-K) of length L =10 mm, thickness i =1 mm, and width w» t. The base temperature of the finis Ty = 150°C, and the finis exposed to a fluid of temperature T, =25°C. Assuming a uniform convection coefficient of h = 110 W/m2.K over the entire fin surface, determine the fin heat transfer rate per unit width 4; efficiency ng: effectiveness es, thermal resistance per unit width and the tip temperature T...
please show derivation of the nodal equations and how to create
the graphs.
A straight fin of uniform cross section is fabricated from a material of thermal conductivity 50 W/m*K, thickness w 6mm, and length L-48mm, and is very long in the direction normal to the page. The convection heat transfer coefficient is 500 W/m2 *K with the ambient air temperature of T-30C. The base of the fin is maintained at Tb = 100C, while the fin tip is will...
Problem 3: Ordinary Differential Equations A straight fin of uniform rectangular cross section (0.5 mm x 100 mm) with a length (L) of 5 cm is attached to a base surface of temperature 110°C (T). The surface of the fin is exposed to a cooling fluid at 20°C (T) with a convection heat transfer coefficient (h) of 15 W/(m²K). The conductivity (k) of the fin material is 400 W/(m.K). (a) Plot the temperature profile along the length of the fin,...
1)
2)
3)
PROJECT #1 (2.5 Marks): The heat that is conducted through a body must frequently be removed by other heat transter processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width Z 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature 1. The conductivity of the aluminum...
The heat that is conducted through a body must frequently be removed by other heat transfer processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature T. The conductivity of the aluminum fin (k) and coefficient of heat convection of...
4. A silicon chip is attached with a copper pin fin in order to enhance the heat transfer. The square shape silicon chip has a width of W=10 mm on each side. The length and diameter of the copper pin are L=20 mm and D=4 mm, respectively. During the operation, the surface of the chip, as well as the base of the pin, are maintained at the temperature of To=375 K. The thermal conductivity of the copper pin fin is...
4. A silicon chip is attached with a copper pin fin in order to enhance the heat transfer. The square shape silicon chip has a width of W=10 mm on each side. The length and diameter of the copper pin are L=20 mm and D=4 mm, respectively. During the operation, the surface of the chip, as well as the base of the pin, are maintained at the temperature of To=375 K. The thermal conductivity of the copper pin fin is...
Most questions answered within 3 hours.
-
(Expected rate of return and risk) Carter Inc. is evaluating a
security. Calculate the investment’s expected...
asked 2 hours ago -
What specific indicators can point to lack of progress for
African Americans in American society?
asked 3 hours ago -
1-The Electrons in a beam are moving at 2.7×108 m/s in an
electric field of 15000...
asked 3 hours ago -
A gas tank is a vertical cylinder. It has a radius of 1m, a
height of...
asked 3 hours ago -
Accent Software faces the following conditions. All of these
support Accent’s use of a market-penetration pricing...
asked 4 hours ago -
A mathematically inclined friend emails you the following
instructions: "Meet me in the cafeteria the first...
asked 4 hours ago -
A monopoly sells in two countries . The demand curves in the two
countries are p1...
asked 5 hours ago -
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 6 hours ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 6 hours ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 7 hours ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 7 hours ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 7 hours ago