We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Question 3: (2 points) controller (K. - 2 and t 2 min) is used to control the reactor temperature...
At steady-state, the output of a PID controller is 10mA. When the process is upset, the set-point signal increases at a rate of 0.4 mA/min. If the controller gain, reset time, and derivative time are 3, 2 min, and 0.4 min, respectively, develop an expression for the controller output, p(t), and plot it as a function of t in Excel (print the plot and attach it to your answer sheet).
QUESTION 7 An electronie P1 Proportional-Integral temperature controleris at steady state with an output of 8 mA such that the set pont equals the seady a lemperature. All the error signal to the controller is increased to 10 m ll the controle sellings are Ke 2 (dimenskis), -2 minwhat will be the ou put mA signs in deviation vanablos) from the controller after 2 minutes? [p-2mn
(2) Solow Model Arithmetic: Suppose that the economy has the following production function: K >0 The population grows at the exogenously given rate n, so that N n)N (a) Derive the per worker production function, where y-Y/N is output per worker and k = K/N is capital per worker (b) Derive the aggregate accumulation equation for capital per worker expressed solely as a function of k. k', A, and parameters (s. θ, d, n). Recall the law of motion for...
(2) Solow Model Arithmetic: Suppose that the economy has the following production function K >O The population grows at the exogenously given rate n, so that N-(1+n)N (a) Derive the per worker production function, where y- Y/N is output per worker and k = K/N is capital per worker. (b) Derive the aggregate accumulation equation for capital per worker expressed solely as a function of k, ,A, and parameters (s,8, d,n). Recall the law of motion for capital: (e) Show...
(2) Solow Model Arithmetic: Suppose that the economy has the following production function: K > 0 n > The population grows at the exogenously given rate n, so that N,-(1 + n) (a) Derive the per worker production function, where y - Y/N is output per worker and k- K/N is capital per worker (b) Derive the aggregate accumulation equation for capital per worker expressed solely as a function of k, k', A. and parameters (s, θ, d, n). Recall...
A process has an input as the flow q gal/min, and an output temperature T Fahrenheit. Initially, the process has been operating for long time at input flow 610 gal/min and output temperature 180 Fahrenheit. An operator introduces a step change in the flow rate (q) to a given process at 4:00 O’clock A.M. He changed the flow from 610 gal/min to 650 gal/min. The effect of the input change resulted in a change in the output. The first change in the temperature occurred at...
Formul Question 2 (50 points): Propane gas and burns with 20% excess air entering (molar C, Hs) at 25 C.I atm enters a reactor operating at steady state at 25 C l atm of the carbon entering with the fuel, 94% s) appears in the products at CO2 and the rest as CO. Heat transfer from the reactor occurs te of 1.4 x 10° kJ per kmol or propane. Use your ideal gas tables to answer this question. ite the...
2a. Determine a proper controller so that the feedback control system below will have the damping ratio of < = 0.7 and the natural frequency of n = 10.0 rad/sec. Your choices are: Proportional controller, K Lead controller, 17, a < 1 Lag controller, v a > 1 Proportional + Derivative controller, K (1 + Tas) Proportional + Integral + Derivative controller, K(1+1/(Ts) + Tas) Or Lead Lag controller If the resulting feedback control system has an order greater than...
ent material has the thermal conductivity k and thickness L. The temperature the material is of the form: distribution along the x-direction, T(x) in + Bx2 + C, where A, a, B, and C are constants. The irradiation is fully the material and can be characterized by a uniform volumetric heat generation, W/m3). Assuming 1D steady-state conduction and constant properties. xpressions for the conduction heat fluxes (alx) at the top and bottom surfaces; absorbed by (4 points) (b) Derive an...
control system System Description: The figure 1 and 2 below show, respectively, components and block diagram of a motor and the measurements of velocity (via the tacho unit) and position (via the potentiometer). n represents the gearbox ratio between the rotating shaft and the output shaft. The left-hand side of the diagram represents the controller. A reference set point for the rotating shaft is entered in degrees and this is equivalent voltage. The error is calculated by subtracting the measured...