Homework Answers
Add Answer to:
Oscillator such that its output is conizrf,1+ φ) . Tee Yoput the DSB-SC modulated signal. The noi...
Can you please explain the solution step by step. P.S write needly :) Problem 9.11 Derive...
Can you please explain the solution step by step.
P.S write needly :)
Problem 9.11 Derive an expression for the post-detection signal-to-noise ratio of the coherent receiver of Fig. 9.6, assuming that the modulated signal s0) is produced by sinusoidal modulating wave m(1)-A, cos(2p.J) Perform your calculation for the following two receiver types: (a) Coherent DSB-SC receiver (b) Coherent SSB receiver. Assume the message bandwidth is f. Evaluate these expressions-r the received signal strength is 100 picowatts, the noise spectral...
In a coherent detection process, a sinusoidally modulated DSB-SC wave, s(t) = c(t)m(t) where the carrier...
In a coherent detection process, a sinusoidally modulated DSB-SC wave, s(t) = c(t)m(t) where the carrier wave is c(t) =Accos(2πfct) and the message signal is m(t) = Amcos(2πfmt), is applied to a product modulator using a locally generated sinusoid of Ac’ amplitude and is out of phase by φ with respect to the sinusoidal carrier used in the modulation. (a) Draw the block diagram of the coherent detection process and label the block diagram with the information provided above accordingly....
(2) Find the output of the DSB-SC demodulator shown in Fig.Q2 below, if the local oscillator...
(2) Find the output of the DSB-SC demodulator shown in Fig.Q2 below, if the local oscillator at the receiver has a phase difference of $ . Also find the power of the signal v,(t) Product modulator (mixer) DSB-SC Modulated Signal vít) Low-Pass Filter Demodulated Signal v.(t) s(t)= m(t)4, cos(21f1) cos (21 f1+0) Local Oscillator Fig. 22
Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The...
Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The modulated signal is u(t) = 200 m(t) cos(21tfct), where f=1 MHz. 1. Determine and sketch the spectrum of the AM signal. 2. Determine the average power in the frequency components 3. Find a resonable choice of R and C to design an envelope detector for this DSB-SC AM signal.
Q1. A DSB-SC signal is transmitted over a noisy channel with power spectral density of noise...
Q1. A DSB-SC signal is transmitted over a noisy channel with power spectral density of noise given as, 0, otherwise with B-200 kHz and N 10W Hz. The message bandwidth is 10 kHz and its average power is 10 W. Assume A,-1, 100kHz, and the channel attenuates signal power by a factor of 1000 (-30 dB). Assume that a suitable band-pass filter is used at the receiver to limit out-of-band noise. (a) Determine the average signal power at the receiver...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandw...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
3. The following is the amplitude spectrum of a DSB+carrier AM signal x(f) 1.5 1.5 1.5 1.5 f (Hz)...
3. The following is the amplitude spectrum of a DSB+carrier AM signal x(f) 1.5 1.5 1.5 1.5 f (Hz) 1920 2000 2080 2080 2000 1920 (a) (10 points) Determine the carrier frequency fe the carrier amplitude Ac the mod ulation index ,, and the message signal m(t) of the AM signal. (b) (10 points) Given that μ2Sm 0.18, find the output SNR (in dB) if the received signal includes white noise with a power spectral density of η/2-10-10 W/Hz. (c)...
The input r(t) to a DSBSC receiver is a DSB signal s(t) = A m(t)cos (21fet)...
The input r(t) to a DSBSC receiver is a DSB signal s(t) = A m(t)cos (21fet) corrupted by additive white Gaussian noise with two-sided power spectral density N,/2, where No = 10-12 W/Hz, m(t) is a message signal bandlimited to 10 kHz. Average power of m(t) is Pm = 4 W and Ac = 2 mV. The block diagram of the receiver is shown below. Note that the receiver has filters which have slightly larger bandwidths than a typical DSB...
An SSB modulated signal is transmitted over a noisy channel, having a spectral density of N0/2...
An SSB modulated signal is transmitted over a noisy channel, having a spectral density of N0/2 of 2*10-9 W/Hz. The message bandwidth is 4kHz and the carrier frequency is 200 kHz. Assume that the average received power of the signal is -80 dBm. Determine the post-detection SNR of the receiver.
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt)....
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt). (a) Find X(f) (b) Find the DSB-SC signal x(t) and Xf). (c) Sketch the spectrums of |M(G| and |X(f)|. In the spectrum, identify the USB and LSB spectra. (d) Find the message signal power, m2(t). (e) Find the transmitted power, Sr x2(t). (f Find the massage signal bandwidth, B, and the transmitted signal bandwidth, Br. (g) Describe the demodulation process and find the detected...
Can you please explain the solution step by step.
P.S write needly :)
Problem 9.11 Derive an expression for the post-detection signal-to-noise ratio of the coherent receiver of Fig. 9.6, assuming that the modulated signal s0) is produced by sinusoidal modulating wave m(1)-A, cos(2p.J) Perform your calculation for the following two receiver types: (a) Coherent DSB-SC receiver (b) Coherent SSB receiver. Assume the message bandwidth is f. Evaluate these expressions-r the received signal strength is 100 picowatts, the noise spectral...
(2) Find the output of the DSB-SC demodulator shown in Fig.Q2 below, if the local oscillator at the receiver has a phase difference of $ . Also find the power of the signal v,(t) Product modulator (mixer) DSB-SC Modulated Signal vít) Low-Pass Filter Demodulated Signal v.(t) s(t)= m(t)4, cos(21f1) cos (21 f1+0) Local Oscillator Fig. 22
Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The modulated signal is u(t) = 200 m(t) cos(21tfct), where f=1 MHz. 1. Determine and sketch the spectrum of the AM signal. 2. Determine the average power in the frequency components 3. Find a resonable choice of R and C to design an envelope detector for this DSB-SC AM signal.
Q1. A DSB-SC signal is transmitted over a noisy channel with power spectral density of noise given as, 0, otherwise with B-200 kHz and N 10W Hz. The message bandwidth is 10 kHz and its average power is 10 W. Assume A,-1, 100kHz, and the channel attenuates signal power by a factor of 1000 (-30 dB). Assume that a suitable band-pass filter is used at the receiver to limit out-of-band noise. (a) Determine the average signal power at the receiver...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
3. The following is the amplitude spectrum of a DSB+carrier AM signal x(f) 1.5 1.5 1.5 1.5 f (Hz) 1920 2000 2080 2080 2000 1920 (a) (10 points) Determine the carrier frequency fe the carrier amplitude Ac the mod ulation index ,, and the message signal m(t) of the AM signal. (b) (10 points) Given that μ2Sm 0.18, find the output SNR (in dB) if the received signal includes white noise with a power spectral density of η/2-10-10 W/Hz. (c)...
The input r(t) to a DSBSC receiver is a DSB signal s(t) = A m(t)cos (21fet) corrupted by additive white Gaussian noise with two-sided power spectral density N,/2, where No = 10-12 W/Hz, m(t) is a message signal bandlimited to 10 kHz. Average power of m(t) is Pm = 4 W and Ac = 2 mV. The block diagram of the receiver is shown below. Note that the receiver has filters which have slightly larger bandwidths than a typical DSB...
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt). (a) Find X(f) (b) Find the DSB-SC signal x(t) and Xf). (c) Sketch the spectrums of |M(G| and |X(f)|. In the spectrum, identify the USB and LSB spectra. (d) Find the message signal power, m2(t). (e) Find the transmitted power, Sr x2(t). (f Find the massage signal bandwidth, B, and the transmitted signal bandwidth, Br. (g) Describe the demodulation process and find the detected...
Most questions answered within 3 hours.
-
on april 10, a company acquired land valued at $58,000 in
exchange for 1,000 shares of...
asked 21 seconds from now -
Is
ampicillin or solvents (such as acetone) more effective at killing
off bacteria, in general? Explain...
asked 5 minutes ago -
The current risk-free rate is 4.0% and the market risk premium
is 5.0%. If Ford Motor...
asked 21 minutes ago -
Advances in technology have increased our opportunities to
connect with others. Along with the benefits of...
asked 29 minutes ago -
Compute the interest rate at which $500 per month payments
should grow to accumulate savings of...
asked 30 minutes ago -
The following information pertains to a weekly payroll of Texera
Tile Company:
a. The total wages...
asked 32 minutes ago -
Alice has the RSA public key (n, e) = (11413, 251) and private
key d =...
asked 45 minutes ago -
QUESTION 5
A drug or medicine can reach the brain more effectively by
placing the drug...
asked 49 minutes ago -
Developmental biology
A mouse contains a mutation that results in a failure of their
long
bones...
asked 45 minutes ago -
Rammazzotti, Inc., is looking for feedback on company
performance. The company compares the budget for the...
asked 50 minutes ago -
A manufacturer of chocolate chips would like to know whether its
bag filling machine works correctly...
asked 59 minutes ago -
Consider the student registration business process at
your college:
1.)Describe the steps necessary for you to...
asked 1 hour ago