Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The...
[15 points] You are asked to design a DSB-SC AM modulator to generate a modulated signal km(t)cos(wt+0), where m(t) is a signal band-limited to B Hz. The following figure shows a DSB- SC AM modulator available in the stockroom. The carrier generator available generates not cos(wct), but cos (wct). Explain whether you would be able to generate the desired signal using only this equipment. You may use any kind of filter you like. 3. What kind of filter is required...
4. A DSB-SC signal is modulated by m(t) = 7coswyt + 3coswqt, with f1 = 0.2 kHz, and Ac = 5. (25 points) a. Write an expression for the DSB-SC signal and sketch a picture of this wave. b. Evaluate and sketch the spectrum for this DSB-SC signal. C. Find the value of the normalized average power. d. Find the value of the normalized PEP.
Assume that an AM transmitter is modulated with a video testing signal given by em(t) = =20 + 60 sin (2πf1t), where f1 = 3.57 MHz. Let the carrier signal c(t) = Ac cos(2πfct), where Ac = 100 and fc = 100 MHz. The AM signal is fed into a 50-Ω load. (a) Derive an expression for the AM DSB-FC signal in time domain. (b) Construct the AM waveform, giving numerical values of the maximum amplitude, Amax and the minimum...
When a baseband signal m(t) = cos(1000t)cos(3000t) is AM modulated using a carrier cos(10,000t), a) Find the frequency components in the baseband signals and in the AM signal. [2] b) Sketch the spectrum, carefully label the graph. c) Find the power efficiency, n. [1] [1]
1. A modulating signal m(t) is given by m(t) = (cos(20nt) – cos(40nt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection
1. A modulating signal m(t) is given by m(t) = (cos(20nt) – cos(40ſt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection. 15 nts
1. A modulating signal m(t) is given by m(t) = 5 (cos(20nt) – cos(40nt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection.
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt). (a) Find X(f) (b) Find the DSB-SC signal x(t) and Xf). (c) Sketch the spectrums of |M(G| and |X(f)|. In the spectrum, identify the USB and LSB spectra. (d) Find the message signal power, m2(t). (e) Find the transmitted power, Sr x2(t). (f Find the massage signal bandwidth, B, and the transmitted signal bandwidth, Br. (g) Describe the demodulation process and find the detected...
1. Given a baseband signal m(t) sin(1000mt) cos(3000nt) + cos(3700nt a. Sketch the spectrum of m(t) (Hint. sin(a) cos(b) 0.5 sin(a +b) +0.5sin a-b)) b. Sketch the spectrum of DSB-CS signal m(t)cos(10000mt) C ldentify the upper sideband {USB) and lower sideband (LSB) spectra d. Give the black diagram of the receiver to receive DSB-CS signal in (b). 2. baseband signal m(r)--0.5 + Σ..小(t-n)-u(t-0.5-n)] where ult) is the Given unit step function, an amplitude modulated signal is as SAM 107+ m(0cos...
Consider the message signal m(t):a. Sketch the AM signal u(t)=[ A + m(t) ] Cos(wct) for modulation indexes μ = 0.5 and μ = 2.0 by assuming the carrier frequency to be much higher than the bandwidth of m(t) b. Determine the efficiency percentage (η = ps/pt) for μ = 0.5. Herein, Ps and Pt are sideband and total powers respectively, and Pt= Ps + Pc , in which Pc is the carrier power. Hint : Take into account the Parseval's property. c. If the AM waveforms corresponding...