4. A DSB-SC signal is modulated by m(t) = 7coswyt + 3coswqt, with f1 = 0.2...
Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The modulated signal is u(t) = 200 m(t) cos(21tfct), where f=1 MHz. 1. Determine and sketch the spectrum of the AM signal. 2. Determine the average power in the frequency components 3. Find a resonable choice of R and C to design an envelope detector for this DSB-SC AM signal.
In a coherent detection process, a sinusoidally modulated DSB-SC wave, s(t) = c(t)m(t) where the carrier wave is c(t) =Accos(2πfct) and the message signal is m(t) = Amcos(2πfmt), is applied to a product modulator using a locally generated sinusoid of Ac’ amplitude and is out of phase by φ with respect to the sinusoidal carrier used in the modulation. (a) Draw the block diagram of the coherent detection process and label the block diagram with the information provided above accordingly....
Assume that an AM transmitter is modulated with a video testing signal given by em(t) = =20 + 60 sin (2πf1t), where f1 = 3.57 MHz. Let the carrier signal c(t) = Ac cos(2πfct), where Ac = 100 and fc = 100 MHz. The AM signal is fed into a 50-Ω load. (a) Derive an expression for the AM DSB-FC signal in time domain. (b) Construct the AM waveform, giving numerical values of the maximum amplitude, Amax and the minimum...
[15 points] You are asked to design a DSB-SC AM modulator to generate a modulated signal km(t)cos(wt+0), where m(t) is a signal band-limited to B Hz. The following figure shows a DSB- SC AM modulator available in the stockroom. The carrier generator available generates not cos(wct), but cos (wct). Explain whether you would be able to generate the desired signal using only this equipment. You may use any kind of filter you like. 3. What kind of filter is required...
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt). (a) Find X(f) (b) Find the DSB-SC signal x(t) and Xf). (c) Sketch the spectrums of |M(G| and |X(f)|. In the spectrum, identify the USB and LSB spectra. (d) Find the message signal power, m2(t). (e) Find the transmitted power, Sr x2(t). (f Find the massage signal bandwidth, B, and the transmitted signal bandwidth, Br. (g) Describe the demodulation process and find the detected...
1. A modulating signal m(t) is given by m(t) = (cos(20nt) – cos(40nt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection
In a DSB-SC amplitude modulation system, the message signal is m(t)=e^(-3t)*u(t-2) and the carrier signal is ???( 2000??). Find the Fourier transform of the modulated signal.
1. A modulating signal m(t) is given by m(t) = (cos(20nt) – cos(40ſt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection. 15 nts
1. A modulating signal m(t) is given by m(t) = 5 (cos(20nt) – cos(40nt)) a. Find and sketch the spectrum of DSB-SC signal 2m(t)cos (100nt) b. Verify that the DSB-SC modulated signal can be recovered using coherent detection.
(2) Find the output of the DSB-SC demodulator shown in Fig.Q2 below, if the local oscillator at the receiver has a phase difference of $ . Also find the power of the signal v,(t) Product modulator (mixer) DSB-SC Modulated Signal vít) Low-Pass Filter Demodulated Signal v.(t) s(t)= m(t)4, cos(21f1) cos (21 f1+0) Local Oscillator Fig. 22