A pair of straight bevel gears are mounted on shafts that are 90 degrees apart, and pinion transmits 10 hp at 300 rpm. The pinion has 6" outside pitch diameter, 2" face width, 20 teeth and Φ =...
A pair of straight bevel gears are mounted on shafts that are 90 degrees apart, and pinion transmits 10 hp at 300 rpm. The pinion has 6" outside pitch diameter, 2" face width, 20 teeth and Φ = 20˚. For a velocity ratio of 0.5, draw a free body diagram of gears showing all forces. What is torque produced about gear axis? The average pinion pitch diameter is 5.104"
Homework Answers
Add Answer to:
A pair of straight bevel gears are mounted on shafts that are 90 degrees apart, and pinion transmits 10 hp at 300 rpm. The pinion has 6" outside pitch diameter, 2" face width, 20 teeth and Φ =...
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is 2 in. The pinion rotates at 1000 rev/min and transmits 50 hp. The shafts are...
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is 2 in. The pinion rotates at 1000 rev/min and transmits 50 hp. The shafts are at 90. Determine the components of the gear tooth force and show these on a sketch of the ge
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is...
A 20° full depth straight tooth bevel gear has a pitch of 3, a face width...
A 20° full depth straight tooth bevel gear has a pitch of 3, a face width of 9.75 in., a pitch diameter of 12.0 in., and a cone pitch angle of 37.5. If the torque on the gear is 6500 in-lb, what is the axial component, or thrust component, of the tooth force? What is the mean diameter of the gear? What is the tangential force at the mean radius? 5. Ans. 297 lb, 4.86 in, 1340 lb.
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/i...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a pinion directly above it. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. Figure P12-1 Shaft carrying a gear and a V-belt drive 0
See Figure P12-1. The shaft rotating...
Question is in Metric not imperial MEA35TA/101/0/2019 Question 9 An uncrowned straight-bevel pinion has 30 teeth, a diametral pitch of 6, and a transmission accuracy number of 6. The driven gear h...
Question is in Metric not imperial
MEA35TA/101/0/2019 Question 9 An uncrowned straight-bevel pinion has 30 teeth, a diametral pitch of 6, and a transmission accuracy number of 6. The driven gear has 60 teeth. Both are made of No. 30 cast iron. The shaft angle is 90 . The face width is 1.25 in, the pinion speed is 900 rev/min, and the normal pressure angle is 20.. The pinion is mounted outboard of its bearings: the bearings of the gear...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a pinion directly above it. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. Figure P12-1 Shaft carrying a gear and a V-belt drive C D 10.004-10.00 6.00 V-belt sheave Gear...
A speed reducer has 20° full-depth teeth with a diametral pitch of 4 teeth/in, a face...
A speed reducer has 20° full-depth teeth with a diametral pitch of 4 teeth/in, a face width of 3.25 inches, and with the pinion having 22 teeth and the gear having 60 teeth. The pinion is driven by a 40 HP motor rotating with a shaft speed of 1145 rpm. The pinion is designed to last for 5 years operating around the clock. The gears are manufactured using 4340 through-hardened grade 1 steel, both heat treated to 250 HB using...
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shaft...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Desgin 0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Question #5 (20 pts) A pinion has 18 teeth and a diametral pitch of 9 teeth/in, a face width of 1,5 in sa pressure angle of 20° with full-depth teeth. The spur gear is made by the milling or emi...
Question #5 (20 pts) A pinion has 18 teeth and a diametral pitch of 9 teeth/in, a face width of 1,5 in sa pressure angle of 20° with full-depth teeth. The spur gear is made by the milling or emin required to transmit at least 11 hp horsepower with a corresponding speed and moderate applications. Which material is the best choice for the spu ones in Table 5 considering the maximum allowable bending stres (factor of safety, nd-2.5)? U quations...
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is 2 in. The pinion rotates at 1000 rev/min and transmits 50 hp. The shafts are at 90. Determine the components of the gear tooth force and show these on a sketch of the ge
27 Two 20° straight bevel gears have a diametral pitch of 4, and 24 and 48 teeth, respectively The tooth face width is...
A 20° full depth straight tooth bevel gear has a pitch of 3, a face width of 9.75 in., a pitch diameter of 12.0 in., and a cone pitch angle of 37.5. If the torque on the gear is 6500 in-lb, what is the axial component, or thrust component, of the tooth force? What is the mean diameter of the gear? What is the tangential force at the mean radius? 5. Ans. 297 lb, 4.86 in, 1340 lb.
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a pinion directly above it. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. Figure P12-1 Shaft carrying a gear and a V-belt drive 0
See Figure P12-1. The shaft rotating...
Question is in Metric not imperial
MEA35TA/101/0/2019 Question 9 An uncrowned straight-bevel pinion has 30 teeth, a diametral pitch of 6, and a transmission accuracy number of 6. The driven gear has 60 teeth. Both are made of No. 30 cast iron. The shaft angle is 90 . The face width is 1.25 in, the pinion speed is 900 rev/min, and the normal pressure angle is 20.. The pinion is mounted outboard of its bearings: the bearings of the gear...
See Figure P12-1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6. The teeth are of the 20%, full-depth, involute form. The gear receives 30 hp from a pinion directly above it. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. Figure P12-1 Shaft carrying a gear and a V-belt drive C D 10.004-10.00 6.00 V-belt sheave Gear...
A speed reducer has 20° full-depth teeth with a diametral pitch of 4 teeth/in, a face width of 3.25 inches, and with the pinion having 22 teeth and the gear having 60 teeth. The pinion is driven by a 40 HP motor rotating with a shaft speed of 1145 rpm. The pinion is designed to last for 5 years operating around the clock. The gears are manufactured using 4340 through-hardened grade 1 steel, both heat treated to 250 HB using...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Question #5 (20 pts) A pinion has 18 teeth and a diametral pitch of 9 teeth/in, a face width of 1,5 in sa pressure angle of 20° with full-depth teeth. The spur gear is made by the milling or emin required to transmit at least 11 hp horsepower with a corresponding speed and moderate applications. Which material is the best choice for the spu ones in Table 5 considering the maximum allowable bending stres (factor of safety, nd-2.5)? U quations...
Most questions answered within 3 hours.
-
What specific indicators can point to lack of progress for
African Americans in American society?
asked 47 minutes ago -
1-The Electrons in a beam are moving at 2.7×108 m/s in an
electric field of 15000...
asked 1 hour ago -
A gas tank is a vertical cylinder. It has a radius of 1m, a
height of...
asked 1 hour ago -
Accent Software faces the following conditions. All of these
support Accent’s use of a market-penetration pricing...
asked 2 hours ago -
A mathematically inclined friend emails you the following
instructions: "Meet me in the cafeteria the first...
asked 2 hours ago -
A monopoly sells in two countries . The demand curves in the two
countries are p1...
asked 3 hours ago -
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 4 hours ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 4 hours ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 4 hours ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 5 hours ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 5 hours ago -
4. How many input & output Key Value Pairs are passed into,
and emitted out of...
asked 5 hours ago