g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...

Question

Question

g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runne

engineering Mechanical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

2 For 5 mould 1 06 o mm - or Kunner pro]ec pxA Hence Force Fc 315000

Add a comment

Answer 2

Similar Homework Help Questions

The brake, shown in figure below, is 300 mm in diameter and is actuated by a mechanism that exerts the same force F on each shoe

The brake, shown in figure below, is 300 mm in diameter and is actuated by a mechanism that exerts the same force F on each shoe. The shoes are identical an have a face width of 30 mm. The lining is a of ceramic type having a coefficient friction of 0.35 and a pressure limitation of 1.1 MPa. Find the following: (a) Actuating force F. (b) Braking torque capacity
4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The an...

4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The answer to each part of the question is to be used for subsequent parts (a)Determine the stresses on the outer surface of the cylinder at points A and B due to (8 marks) (b) Determine the minimum internal pressure p required if the...
A cylindrical bar of ductile cast iron is subjected to reversed and rotating-bending tests, test results (i.e., S-N behavior) are shown in Animated Figure 8.21. If the bar diameter is 8.52 mm, determi...

A cylindrical bar of ductile cast iron is subjected to reversed and rotating-bending tests, test results (i.e., S-N behavior) are shown in Animated Figure 8.21. If the bar diameter is 8.52 mm, determine the maximum cyclic load that may be applied to ensure that fatigue failure will not occur. Assume a factor of safety of 2.21 and that the distance between loadbearing points is 55.3 mm. answer in N We were unable to transcribe this imageReferences Cycles to failure 3.2E...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...

g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...

Homework Answers

Add Answer to:
g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...

Post as a guest

Earn Coins

The brake, shown in figure below, is 300 mm in diameter and is actuated by a mechanism that exerts the same force F on each shoe

4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The an...

A cylindrical bar of ductile cast iron is subjected to reversed and rotating-bending tests, test results (i.e., S-N behavior) are shown in Animated Figure 8.21. If the bar diameter is 8.52 mm, determi...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...

Homework Answers

Add Answer to: g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...

Post as a guest

Earn Coins

The brake, shown in figure below, is 300 mm in diameter and is actuated by a mechanism that exerts the same force F on each shoe

4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The an...

A cylindrical bar of ductile cast iron is subjected to reversed and rotating-bending tests, test results (i.e., S-N behavior) are shown in Animated Figure 8.21. If the bar diameter is 8.52 mm, determi...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

Add Answer to:
g) An injection mould is setup as shown in Figure below. The pressure applied is 70 MPa and assume that the diameter of runner is 7 mm and length of runner is 500 mm. Calculate the mould-clamping for...